Spare parts category
hoses
hoses spare parts for Bosch and Siemens dishwashers. All 19 parts have verified OEM compatibility data.
19 parts · All OEM-verified
Clamp,circulation Pump,flow Control Regulator,35.6mm/3mm
OEM: 8078689026
If your AEG dishwasher isn't circulating water properly or you've noticed leaks around the pump area, this circulation pump clamp is likely the culprit. Over time, the clamp holding your flow control regulator in place can weaken or fail, causing water to escape and reducing cleaning performance. This genuine replacement part (OEM reference 8078689026) restores a secure seal between the pump and hose connections, getting your dishwasher back to working efficiently. The 35.6mm/3mm dimensions are precisely engineered to fit AEG models. Installation difficulty is rated at just 2 out of 5, making this a manageable DIY job for most homeowners. Our practical tip: before tightening the clamp fully, ensure the hose is seated properly in the connector to avoid pinching or misalignment. Take your time with this step and you'll achieve a watertight fit first time. This is a hose category component that addresses general wear and failure issues common in older dishwashers. Before ordering, please verify your appliance's E-Nr model number matches our compatibility list to ensure correct fitment.
Compatible with 44 models
Clamp,circulation Pump,sump,44.4mm/3.2mm
OEM: 8078689034
When your AEG dishwasher stops cleaning properly or leaks around the pump area, a worn circulation pump clamp is often the culprit. Over time, this essential component deteriorates from constant exposure to water and heat, causing the hose connection to loosen and fail. This genuine replacement clamp (OEM reference 8078689034) secures the circulation pump outlet hose in place, maintaining proper water flow throughout your wash cycle. Without it, you'll experience reduced cleaning performance or pooling water inside the machine. The good news is that replacing this part is straightforward. With an install difficulty rating of just 2 out of 10, most DIY homeowners can tackle this job in under an hour. Our top tip: before tightening the clamp fully, ensure the hose sits evenly in the groove to prevent pinching or misalignment. This hose clamp is categorised as essential maintenance for AEG dishwashers experiencing general wear and failure. It's an affordable fix that prevents more costly damage down the line. Before ordering, please verify your dishwasher's E-Nr model number matches the compatibility information to ensure this is the correct part for your machine.
Compatible with 44 models
Clamp, Drain Hose, 30mm/2.8mm
OEM: 8078689018
Water leaking from your AEG dishwasher's drain hose is often caused by a worn or damaged clamp that no longer grips securely. This genuine OEM replacement clamp (reference 8078689018) restores a watertight seal and prevents water damage to your kitchen flooring and cabinets. Over time, the metal clamp gradually loses tension through repeated heating and cooling cycles, or corrosion may compromise its integrity. Replacing it is a straightforward solution that costs far less than repairing water damage. Installation difficulty is rated at level 2, making this an achievable DIY task for most homeowners. The 30mm diameter clamp fits standard drain hose connections. When fitting the new clamp, ensure you position it evenly around the hose connector and tighten it gradually rather than forcing it fully in one go, which helps prevent distortion. Before ordering, verify your dishwasher's E-Nr model number (found on the internal side wall or door edge) matches the compatibility list. This ensures you receive the correct part for your specific AEG model.
Compatible with 44 models
Dishwasher Discharge Hose Flange
OEM: 8072019014
Is your AEG dishwasher leaking water or failing to drain properly? A worn or damaged discharge hose flange is often the culprit. Over time, this connector can deteriorate due to constant water exposure and pressure, leading to leaks underneath your appliance or poor drainage performance. This genuine replacement flange, reference 8072019014, restores the secure connection between your dishwasher's drain system and the outlet hose. It's a straightforward repair that most confident DIYers can tackle in under an hour, rated at difficulty level 2. When you're ready to install, make sure to position the flange carefully before tightening the retaining clips. Apply gentle, even pressure to avoid cracking the plastic connector. There's no need to force anything; if resistance builds, double-check your alignment first. This is a genuine OEM part built to AEG's exacting standards, ensuring reliable performance and lasting durability. Before placing your order, please verify the E-Nr model number on your dishwasher to confirm compatibility with reference 8072019014.
Compatible with 43 models
Outlet Hose, L=2340mm
OEM: 140005633064
If water is pooling beneath your AEG dishwasher or leaking from the back, a worn or damaged outlet hose is likely the culprit. Over time, these hoses can crack, split, or become brittle, preventing proper water drainage and causing costly water damage to your kitchen. This genuine OEM outlet hose (reference 140005633064) restores proper drainage function and returns your dishwasher to reliable operation. At 2340mm in length, it's designed specifically for AEG models to ensure a perfect fit and optimal performance. Installation difficulty is rated as straightforward, making this an ideal DIY repair for confident homeowners. The key tip is to turn off the water supply and empty the dishwasher completely before disconnecting the old hose. Take a photo of the connection points beforehand so you know exactly how to reattach the new one. This part addresses general wear and failure issues that naturally occur with extended use. Before ordering, verify your dishwasher's E-Nr model number matches our compatibility list, as this ensures you receive the correct replacement and avoid unnecessary returns.
Compatible with 43 models
Hose, Sump, Water Softener, D20x185mm
OEM: 140000602031
If your AEG dishwasher isn't draining properly or you've noticed water pooling inside, a worn sump hose could be the culprit. This essential component connects your water softener to the sump pump, and over time it can crack, split, or lose its seal, causing leaks and drainage issues that prevent your dishwasher from completing its cycle. Replacing this hose is a straightforward DIY job, rated at difficulty level 2. You'll need to access the base of your appliance and disconnect the old hose before fitting the new one. Our top tip: before you start, take a photo of how the existing hose connects, as this will guide you when reconnecting. Also, place a towel underneath as residual water may spill during removal. This is a genuine OEM part, reference number 140000602031, designed specifically for AEG dishwashers to ensure perfect compatibility and reliable performance. Before ordering, please verify your dishwasher's E-Nr model number matches this part's specifications. You'll find this on your appliance's rating plate, usually inside the door edge.
Compatible with 37 models
Kit, Overflow Hose, Conveyor,
OEM: 4055250858
Water pooling inside your dishwasher or leaking onto your kitchen floor is often caused by a worn or damaged overflow hose. Over time, this rubber component can crack, split, or become brittle, losing its ability to safely channel excess water away from your appliance's interior. Replacing a faulty overflow hose kit is a straightforward solution that prevents potential water damage to your kitchen cabinets and flooring. This genuine OEM overflow hose conveyor kit (reference 4055250858) is designed specifically for AEG dishwashers and restores proper water management to your machine. The installation difficulty is rated at 2 out of 5, making it an achievable project for most confident DIY homeowners with basic tools. When installing, ensure the hose connections are pushed firmly onto their fittings until you hear a subtle click or feel resistance. This simple step prevents future leaks and guarantees a secure seal. Before placing your order, please verify your dishwasher's E-Nr model number on the inside of the door frame or product manual to confirm compatibility with this part.
Compatible with 26 models
Wrflex100 Dishwasher Hous
OEM: 9117405242
Is your AEG dishwasher leaking or failing to drain properly? A worn or damaged inlet hose is often the culprit, and replacing it is a straightforward fix that most homeowners can handle in under an hour. The WRFLEX100 hose assembly is a genuine replacement part designed to restore your dishwasher's performance. Whether your existing hose has developed cracks, become brittle with age, or simply reached the end of its service life, this component will get your appliance working reliably again. The OEM reference 9117405242 ensures you're getting the exact part your dishwasher needs. Installation difficulty is rated as just 2 out of 5, making this an ideal DIY project. The main tip is to place a shallow tray or towel underneath before you start, as residual water will inevitably spill during removal. Take a photo of your current setup before disconnecting anything, and the reassembly process becomes much easier. Before ordering, verify your dishwasher's E-Nr model number, which you'll find on the inside of the door frame. This ensures complete compatibility with your specific AEG model.
Compatible with 26 models
Inlet Hose,aqua-control,l=1475mm
OEM: 140180589081
Water not filling your AEG dishwasher properly, or noticing leaks underneath? A worn or damaged inlet hose is often the culprit. Over time, the aqua-control inlet hose can deteriorate due to water pressure, temperature changes, and general wear, leading to reduced water flow or troublesome puddles on your kitchen floor. This genuine OEM replacement hose (reference 140180589081) restores proper water delivery to your appliance, ensuring your dishes get cleaned effectively without the worry of water damage. At 1475mm in length, it's designed to fit perfectly with your AEG dishwasher model. The installation difficulty rating of 2 means most confident DIY homeowners can tackle this job without professional help. Our practical tip: before removing the old hose, place a towel underneath to catch any residual water in the system. This simple precaution keeps your kitchen dry and makes cleanup easier. To ensure compatibility and avoid ordering errors, please verify your dishwasher's E-Nr model number before purchasing. You'll find this on your appliance's identification plate, typically located inside the door edge.
Compatible with 21 models
Dishwasher Hose Clamp
OEM: 1526417009
Water leaks from your dishwasher hoses or loose connections coming adrift during the wash cycle are common signs that your hose clamp needs replacing. Over time, these metal clamps corrode, weaken or lose their grip, allowing hoses to slip and cause water damage beneath your kitchen units. This genuine AEG replacement hose clamp (OEM reference 1526417009) restores a secure, watertight seal between your dishwasher's inlet and outlet hoses. It's a straightforward fix that most DIY homeowners can tackle in under an hour, rated at difficulty level 2. When installing, remember to fully drain your dishwasher and unplug it before accessing the hoses. Position the clamp squarely over the hose connection and tighten evenly to avoid pinching the rubber. Don't over-tighten, as this can damage the hose itself. This part fits AEG dishwashers, so verify your appliance's E-Nr model number before ordering to ensure compatibility. You'll find this printed on the inside edge of your door or in your user manual.
Compatible with 17 models
Inlet Hose,aqua-control,l=1475mm
OEM: 140180589016
Water pooling beneath your AEG dishwasher or leaks during the wash cycle usually point to a failing inlet hose. Over time, these hoses can crack, perish or develop splits that compromise their water-tight seal, leaving you with water damage and an appliance that won't run properly. This replacement inlet hose is the genuine OEM part (reference 140180589016) designed specifically for AEG dishwashers. At 1475mm in length, it's pre-fitted with aqua-control technology to regulate water flow safely into your machine. Installation is straightforward, rated as difficulty level 2, making it an ideal DIY job for most homeowners. When fitting your new hose, always ensure both connection points are fully secured and hand-tightened before running a test cycle. This simple step prevents future leaks at the joints. Before ordering, verify your dishwasher's E-Nr model number matches the compatibility information on your product page. This ensures you receive the correct part first time, saving you time and hassle.
Compatible with 17 models
Water Sump
OEM: 140000494413
If your AEG dishwasher isn't draining properly or you've noticed water pooling at the base of the unit, a worn water sump could be the culprit. This component is essential for collecting and directing water towards the drain, and like all rubber parts, it naturally deteriorates over time through regular use. This genuine water sump (OEM reference 140000494413) is designed to restore proper drainage function to your dishwasher, eliminating leaks and ensuring your appliance runs efficiently once more. Installation difficulty is rated at level 2, making this a manageable job for most DIY homeowners. When fitting the new sump, remember to inspect the surrounding hoses for any cracks or damage whilst you have access to the area. Replacing a damaged sump alongside compromised hoses can prevent future problems and save you time. Before ordering this part, please verify your dishwasher's E-Nr model number against the compatibility information. This ensures you're purchasing the correct component for your specific AEG model, avoiding costly mistakes and delays.
Compatible with 12 models
Dishwasher Inlet Hose Reducer Ring Nut
OEM: 1240681013
Water leaks around your dishwasher's inlet connection or reduced water flow during the wash cycle often point to a worn reducer ring nut. This small but essential component creates a watertight seal where the supply hose connects to your appliance, and over time, the threads can deteriorate or the seal can fail completely. The inlet hose reducer ring nut (OEM reference 1240681013) is the affordable solution to restore your AEG dishwasher's performance. Replacement is straightforward, rated at difficulty level 2, making it ideal for confident DIY homeowners tackling appliance repairs at home. Installation requires only a basic adjustable wrench or spanner to unscrew the old nut and thread the new one into place. A practical tip: wrap a small cloth around the fitting before tightening to prevent scratching the chrome surface. This genuine spare part ensures a reliable connection and eliminates frustrating leaks that can damage kitchen flooring. Stock this replacement if you're performing routine dishwasher maintenance. Before ordering, please verify your dishwasher's E-Nr model number matches our compatibility list to guarantee the correct part for your machine.
Compatible with 11 models
Inlet Hose,aqua-control,[1825mm]
OEM: 140180589099
Water won't fill your AEG dishwasher, or you've spotted a leak underneath? A worn or damaged inlet hose is often the culprit. Over time, these hoses can crack, split, or lose their seal, preventing water from reaching your appliance or causing pooling water on your kitchen floor. Replacing the hose is usually a straightforward fix that gets your dishwasher running again. This genuine inlet hose (OEM reference 140180589099) is designed specifically for AEG dishwashers and features aqua-control technology for reliable water management. Installation difficulty is rated at level 2, making it accessible for most confident DIY homeowners. The most practical tip when fitting a new hose is to turn off the water supply at the mains before disconnecting the old one. This prevents any unexpected water spillage and makes the job cleaner and safer. Ensure both the inlet connection and the hose itself are completely dry before attaching the new hose for a watertight seal. Before ordering, please verify the E-Nr model number of your dishwasher to confirm compatibility with this part.
Compatible with 11 models
Dishwasher Overflow Hose Kit
OEM: 4055113080
Water pooling under your AEG dishwasher or leaking during the cycle? A worn or damaged overflow hose is often the culprit. This essential component prevents water from backing up into your machine, and when it fails, you'll quickly notice puddles on your kitchen floor or water damage to your cabinets below. The Dishwasher Overflow Hose Kit (OEM reference 4055113080) is a straightforward replacement that restores proper drainage and protects your kitchen from water damage. Installation difficulty sits at level 2, making this a manageable DIY job for most homeowners without requiring a professional engineer. Before you begin, locate where the hose connects to your dishwasher's drain system and note the routing underneath. When installing your new kit, ensure all connections are pushed firmly onto their fittings and consider using a small hose clamp to secure joints if they seem loose. This prevents future leaks and extends the component's lifespan. Please verify your AEG dishwasher's E-Nr model number before ordering to ensure complete compatibility with your appliance.
Compatible with 7 models
Dishwasher Inlet Hose
OEM: 1526125701
Water not reaching your AEG dishwasher, or pooling underneath? A worn or damaged inlet hose is often the culprit. Over time, these hoses can crack, split or develop weak points that compromise water flow or cause leaks. Replacing it is a straightforward fix that can restore your appliance to full working order. This genuine OEM inlet hose (reference 1526125701) is designed specifically for AEG dishwashers and offers reliable performance. Installation sits at difficulty level 2, meaning most confident DIY homeowners can manage it without professional help. The job typically takes under an hour. When fitting the new hose, we recommend having a towel or shallow tray nearby to catch any residual water from the old hose before disconnection. This simple precaution saves mess and makes the job cleaner overall. Before ordering, please verify your dishwasher's E-Nr model number against our compatibility information. You'll find this on the appliance's identification plate, usually inside the door edge. Checking this detail ensures you receive the correct part first time.
Compatible with 6 models
Outlet Hose, with Ventilation
OEM: 140011410085
If your AEG dishwasher isn't draining properly or you've spotted water pooling beneath the appliance, a worn or damaged outlet hose is likely the culprit. Over time, these hoses can crack, perish, or become blocked, preventing water from flowing away efficiently during the wash cycle. This genuine replacement outlet hose with ventilation (OEM reference 140011410085) restores proper drainage to get your dishwasher working reliably again. The ventilation feature prevents vacuum formation in the drain line, which can cause blockages and reduce washing performance. Installation difficulty is rated at level 2, making this a straightforward job for most DIY homeowners. The main practical tip is to have a shallow tray or towels ready when you disconnect the old hose, as water may still be present in the system. Simply unclip or unscrew the old hose from both the dishwasher outlet and drain connection, then fit the new one in reverse order. Before placing your order, please verify your appliance's E-Nr model number matches our compatibility information to ensure you're purchasing the correct part.
Compatible with 4 models
Ventilating Tube,beige,l=1570mm
OEM: 140011411109
When your AEG dishwasher develops drainage issues or you notice water pooling inside the cabinet, a worn or damaged ventilating tube is often the culprit. Over time, these hoses can crack, split or become brittle from repeated heating cycles, compromising your appliance's ability to function properly. This replacement ventilating tube (OEM reference 140011411109) is designed to restore proper airflow and drainage to your dishwasher. At 1570mm in length, it's sized to fit standard AEG models perfectly. The good news is that replacing this hose is relatively straightforward. Rated as a difficulty level 2 repair, most competent DIY homeowners can handle the installation themselves. When fitting the new tube, ensure you secure any clips or brackets firmly but avoid over-tightening, which could crack the beige plastic fitting. Before placing your order, it's essential to verify your dishwasher's E-Nr model number against the product compatibility list. This guarantees you're purchasing the correct part for your specific AEG model and saves unnecessary returns or installation frustration.
Compatible with 2 models
Ventilating Tube, L=1680mm
OEM: 140011411091
If your AEG dishwasher isn't draining properly or you've noticed water pooling at the base of the unit, a worn or damaged ventilating tube is often the culprit. Over time, this essential hose can crack, split, or become blocked, preventing moisture from being safely expelled during the drying cycle. Replacing it restores your dishwasher's performance and prevents potential water damage to your kitchen. This genuine replacement tube measures 1680mm in length and carries the OEM reference 140011411091, ensuring perfect compatibility with your AEG model. Installation difficulty is rated at level 2, making it an achievable project for most confident DIY homeowners. When fitting the new tube, ensure all existing debris or mineral deposits are cleared from the connection points before attaching. This simple step prevents leaks and guarantees a secure seal. This part addresses general wear and failure that naturally occurs with regular use. Before ordering, please verify your dishwasher's E-Nr model number matches our compatibility list. You'll find this information on the appliance's identification plate, usually located inside the door frame.
Compatible with 2 models