Spare parts category
feet_housing
feet_housing spare parts for Bosch and Siemens dishwashers. All 56 parts have verified OEM compatibility data.
56 parts · All OEM-verified
Cover, Heater
OEM: 140002173049
When your AEG dishwasher stops heating properly or you notice visible damage to the heating element housing, a worn heater cover is often the culprit. This essential component protects your dishwasher's heating system from debris and moisture, and over time it can crack, warp, or deteriorate from repeated exposure to heat and steam. Replacing your heater cover is a straightforward repair that most confident DIY homeowners can tackle in under an hour. The installation difficulty rating of 2 means you'll need basic tools and some patience, but no specialist knowledge required. When fitting the new part, ensure you've fully disconnected your dishwasher from the power supply first, then carefully remove the old cover before sliding the new one into position. This genuine replacement component, reference number 140002173049, is specifically designed for AEG dishwashers and guarantees proper fit and function. It's an affordable way to restore your appliance to full working order without calling out an engineer. Before placing your order, please verify your dishwasher's E-Nr model number matches this part's compatibility to ensure you receive the correct component for your specific machine.
Compatible with 44 models
Dishwasher Ventilation Grill
OEM: 1526272214
If your AEG dishwasher is running poorly or showing signs of overheating, a faulty ventilation grill could be the culprit. Poor air circulation inside the appliance leads to moisture buildup, reduced cleaning performance, and potential damage to internal components. This ventilation grill restores proper airflow, helping your dishwasher operate efficiently and safely. The OEM reference 1526272214 is a genuine replacement part designed specifically for AEG models. Installation is straightforward, rated at difficulty level 2, making it perfect for DIY homeowners. Before you start, ensure the dishwasher is unplugged from the mains for safety. The grill typically clips or screws into place within the housing, so you'll need just a basic screwdriver. This part addresses general wear and failure that occurs naturally over time. Regular use can cause the ventilation grill to crack, warp, or deteriorate, compromising your appliance's performance and lifespan. Important: Always verify your dishwasher's E-Nr model number before ordering to guarantee compatibility with this part. You'll find this number on the product information sticker, usually located inside the door edge or side panel.
Compatible with 44 models
Dishwasher Fixing Clips
OEM: 4055046587
Is your AEG dishwasher sitting unevenly or making unusual noises during operation? Worn or damaged feet housing clips are likely the culprit. Over time, these essential components deteriorate through normal use, causing your appliance to lose stability and potentially creating vibration problems during the wash cycle. These genuine fixing clips (OEM reference 4055046587) are designed to securely hold your dishwasher's feet in place, ensuring level positioning and smooth, quiet operation. Replacing them is straightforward, with an install difficulty rating of just 2 out of 10, making this an ideal DIY job for most homeowners. Before you start, locate your dishwasher's model number, typically found on the interior wall or behind the kick panel. Verify that your E-Nr matches our compatibility information to ensure these clips will fit your specific AEG model. Once confirmed, the replacement process is quick and requires minimal tools. Don't let worn feet housing clips compromise your dishwasher's performance. Order your genuine AEG fixing clips today and restore stable, reliable operation to your kitchen appliance.
Compatible with 39 models
Cover, Electronic, Metal,
OEM: 140000750012
When your AEG dishwasher's feet housing cover becomes loose, cracked, or deteriorated, it can affect the appliance's stability and appearance. This genuine metal electronic cover (OEM reference 140000750012) restores proper protection to your dishwasher's base, addressing general wear and failure that occurs over time. The cover plays an important role in keeping debris and moisture away from sensitive components whilst maintaining your dishwasher's structural integrity. Whether your current cover has simply worn down or sustained damage, this replacement part will get your appliance back to working order. Installation is straightforward, rated at difficulty level 2, making it perfectly manageable for most DIY homeowners. Our top tip: before you begin, take a photograph of the existing cover from multiple angles so you can reference the exact positioning when fitting the new one. This simple step ensures proper alignment and a professional finish. This part is compatible with AEG dishwashers, though availability may vary by model. Before ordering, please verify your dishwasher's E-Nr model number, which you'll find on the appliance's data plate, to confirm compatibility with this specific component.
Compatible with 33 models
Cup Shelf
OEM: 140000275036
If your cups and glasses aren't sitting properly in your dishwasher or the shelf has become loose and wobbly, a worn or damaged cup shelf is likely the culprit. Over time, normal use causes wear and failure on this component, compromising both safety and washing performance. This genuine AEG replacement cup shelf (OEM reference 140000275036) restores proper functionality to your appliance. Installation is straightforward, rated at difficulty level 2, making it an ideal weekend project for most homeowners. When fitting the new shelf, ensure you've fully removed the old one first by carefully unclipping it from both sides of the dishwasher interior. Take a moment to inspect the mounting points for any debris or damage before sliding the replacement into position. You'll know it's seated correctly when it clicks firmly at both ends. This part is specifically designed for AEG dishwashers and offers reliable performance that matches your original equipment. Before placing your order, please verify your appliance's E-Nr model number matches this part's compatibility. You'll find this number on your dishwasher's identification plate, usually located inside the door edge.
Compatible with 33 models
Cup Shelf Holder
OEM: 140131012035
If your dishwasher cups aren't sitting securely or your cup shelf has become loose and wobbly, a worn cup shelf holder could be the culprit. Over time, these plastic components experience general wear and failure, particularly if your dishwasher runs frequently. Replacing the faulty holder will restore proper support and stability to your cup shelf, ensuring dishes stay safely in place during the wash cycle. This genuine AEG spare part, reference 140131012035, is designed specifically for AEG dishwashers and offers a straightforward replacement. The installation difficulty is rated at level 2, making it manageable for most DIY enthusiasts with basic tools and a little patience. When installing the new cup shelf holder, take a moment to clean the mounting area thoroughly before fitting the replacement. This removes any debris or mineral deposits that could prevent a secure fit and helps ensure longevity. Before ordering, please verify your dishwasher's E-Nr model number matches our compatibility information. You'll find this printed on the data label inside your machine, usually on the side wall or door edge.
Compatible with 33 models
Dishwasher Aluminium Cover Sheet
OEM: 140030693059
Your AEG dishwasher's feet housing takes a beating from daily use, vibrations, and moisture exposure. Over time, the aluminium cover sheet can wear, crack, or fail completely, leaving the internal mechanisms exposed and potentially causing your appliance to sit unevenly or operate noisily. This genuine OEM replacement cover sheet (reference 140030693059) restores proper protection to the feet housing area, ensuring your dishwasher sits securely and functions as intended. Installation difficulty rates at just 2 out of 10, making this a manageable DIY repair for most homeowners. When fitting the new cover sheet, take care to align it properly with the existing mounting points before tightening any fasteners. This prevents warping and ensures a neat, secure fit that will last for years to come. Whether you're noticing visible damage, loose components, or general wear around the base of your dishwasher, this replacement part offers a straightforward solution. Before placing your order, please verify your appliance's E-Nr model number against the compatibility information to confirm this is the correct part for your specific AEG dishwasher model.
Compatible with 29 models
Dishwasher Central Adjustable Foot
OEM: 1173632009
Is your AEG dishwasher sitting unevenly or making unusual noises during operation? A worn or damaged central adjustable foot could be the culprit. Over time, these feet wear down from regular use, causing the appliance to become unstable and affecting its performance. This genuine replacement foot (OEM reference 1173632009) restores proper levelling to your dishwasher, eliminating wobbling and ensuring smooth operation. The adjustable design allows you to fine-tune your appliance's position for optimal stability and drainage. Installation is straightforward, rated at difficulty level 2, making it ideal for a confident DIY homeowner. The key tip is to adjust all feet evenly once installed, rather than over-tightening one leg. This ensures balanced support and prevents future levelling issues. Before ordering, it's essential to verify your dishwasher's E-Nr model number against our compatibility list. You'll find this number on the appliance's data plate, usually located inside the door edge. Checking this detail now will save time and prevent ordering errors.
Compatible with 29 models
Dishwasher Central Foot Adjusting Screw
OEM: 140000210041
If your dishwasher is sitting unevenly or wobbling during the wash cycle, a worn or damaged central foot adjusting screw could be the culprit. Over time, this component deteriorates through regular use, causing your appliance to lose stability and potentially creating noise or vibration issues. This genuine AEG replacement part (OEM reference 140000210041) restores proper levelling to your dishwasher, ensuring it sits flat and operates smoothly. The installation difficulty is rated as straightforward, making this an ideal DIY repair for most homeowners. When fitting the new screw, we recommend first emptying your dishwasher completely and turning off the water supply. You'll need to access the central foot housing underneath the unit, so having a torch handy will make the job considerably easier. Take a moment to clean away any debris around the foot assembly before installing the replacement. This is a common wear item that extends the lifespan of your appliance and eliminates annoying movement during operation. Before ordering, please verify your dishwasher's E-Nr model number matches our compatibility list to ensure this part is correct for your machine.
Compatible with 29 models
Dishwasher Gear Wheel
OEM: 1527142002
When your AEG dishwasher becomes noisy, unstable, or fails to operate smoothly, a worn gear wheel is often the culprit. This essential component keeps your appliance running reliably, but like all mechanical parts, it gradually wears down with regular use. Replacing it restores proper functionality and prevents further damage to your dishwasher's internal mechanisms. This genuine OEM gear wheel (reference 1527142002) is designed specifically for AEG models, ensuring perfect compatibility and performance. The installation difficulty rating of 2 means most confident DIY homeowners can handle this repair without professional help. Before you start, locate your dishwasher's E-Nr model number, usually found on the inner edge of the door frame or on the appliance's specification plate. This ensures you're ordering the correct part for your specific model. When installing, take a moment to inspect the mounting housing for any additional wear whilst you have access, as this can save time and money on future repairs. Please verify your E-Nr model number before ordering to guarantee compatibility with your AEG dishwasher.
Compatible with 29 models
Front Dishwasher Adjustable Foot
OEM: 1526617020
Is your dishwasher sitting unevenly or making noise during the wash cycle? A worn or damaged adjustable foot could be the culprit. Over time, these feet experience general wear and failure due to constant use and vibration, causing your appliance to become unstable or tilt to one side. This genuine AEG replacement foot (OEM reference 1526617020) restores proper levelling and stability to your dishwasher, eliminating unwanted movement and vibration. It's a straightforward repair that most DIY homeowners can tackle themselves, rated as difficulty level 2. Installation is simple: locate the damaged foot at the front corner of your dishwasher, unscrew the old component, and thread the new adjustable foot into place. A helpful tip is to adjust all four feet evenly once you've installed the replacement, ensuring your dishwasher sits perfectly level. Use a spirit level to check your work—this prevents water from pooling inside and keeps the machine running smoothly. Before ordering, verify your dishwasher's E-Nr model number matches this part's compatibility to ensure you receive the correct component for your AEG appliance.
Compatible with 29 models
Bottom Tray
OEM: 1561831205
If your AEG dishwasher is sitting unevenly or wobbling during operation, a worn or damaged bottom tray is likely the culprit. This essential component supports the appliance's weight and keeps it stable on your kitchen floor. Over time, normal wear and tear can cause it to crack, warp, or deteriorate, compromising both safety and performance. This genuine OEM replacement (reference 1561831205) restores proper stability and ensures your dishwasher operates smoothly without movement or noise. Installation difficulty sits at level 2, making it a manageable DIY task for most homeowners. Before you start, tip the dishwasher slightly forward and place a towel underneath to catch any water that may spill from the drain. This simple precaution saves mess and protects your flooring. The replacement process typically takes under an hour. Once fitted, your dishwasher will run quietly and securely, eliminating any rocking or shifting during cycles. Please verify your appliance's E-Nr model number matches this part's compatibility before ordering to ensure a perfect fit for your specific AEG dishwasher model.
Compatible with 25 models
Soft Spikes, Red, 170x75,5x17.5
OEM: 140159440068
Is your AEG dishwasher moving around during the wash cycle or sitting unevenly on your kitchen floor? Worn or damaged soft spikes feet are the likely culprit. Over time, these protective feet deteriorate from regular use, causing your appliance to become unstable and potentially damaging your kitchen surfaces. These genuine replacement soft spikes feet restore proper levelling and stability to your dishwasher. The red feet measure 170x75.5x17.5mm and are supplied as a housing unit, making installation straightforward for most home mechanics. The OEM reference 140159440068 ensures you're getting the exact part your machine needs. Installation is rated as difficulty level 2, meaning it's manageable for confident DIYers. Our top tip: before fitting the new feet, thoroughly clean the mounting area to remove any debris that could affect grip or levelling. Take time to adjust all feet evenly using a spirit level for best results. Before ordering, please verify the E-Nr model number on your dishwasher's rating plate to confirm compatibility with your specific AEG model.
Compatible with 24 models
Basement, Dnl
OEM: 140000732218
If your AEG dishwasher is wobbling, sitting unevenly, or making unusual noises during operation, worn or damaged feet housing could be the culprit. Over time, the feet that support your appliance naturally deteriorate through regular use, causing instability and potential damage to your kitchen floor and the dishwasher itself. This genuine feet housing basement component (OEM reference 140000732218) restores proper support and levelling to your machine. It's a straightforward replacement suitable for confident DIY homeowners, rated as difficulty level 2, meaning basic tools and mechanical aptitude are all you'll need. When installing, take a moment to adjust the levelling feet properly once you've fitted the new housing. This simple step ensures your dishwasher sits perfectly level, which improves drainage, reduces vibration, and extends the lifespan of your appliance. This part addresses general wear and failure of the feet housing, restoring stability and safe operation to your dishwasher. Before ordering, please verify your machine's E-Nr model number matches this part's compatibility to ensure a correct fit.
Compatible with 11 models
Basket Tines Clamp,upper Basket
OEM: 140001417025
Is your dishwasher's upper basket sitting at an awkward angle or failing to slide smoothly? A worn or broken basket tines clamp could be the culprit. Over time, these plastic clamps deteriorate from repeated use, causing your basket to become unstable or misaligned during the wash cycle. This genuine AEG replacement part (OEM reference 140001417025) restores proper basket support and ensures smooth operation. Installation is straightforward, rated at difficulty level 2, making it an ideal DIY job for most homeowners. When fitting the new clamp, ensure you've fully removed the upper basket first and positioned yourself comfortably underneath the dishwasher interior. Take a moment to inspect the mounting points for any debris or damage before securing the clamp into place. This prevents installation issues and ensures longevity. Most users complete this repair in under fifteen minutes without specialist tools. Fixing this issue promptly prevents further damage to your basket and dishwasher mechanics. Before ordering, please verify your appliance's E-Nr model number matches this part's compatibility to guarantee a perfect fit for your AEG dishwasher.
Compatible with 11 models
Bottom Tray,
OEM: 140000733182
If your dishwasher isn't sitting level or appears unstable, a worn or damaged bottom tray is likely the culprit. This essential component supports the entire unit and deteriorates over time through normal use and moisture exposure. When it fails, you may notice the dishwasher wobbling or rocking, which can lead to further damage if left unaddressed. This genuine AEG replacement bottom tray (OEM reference 140000733182) restores stability and ensures your appliance operates safely. Installation is straightforward, rated at difficulty level 2, making it an ideal project for confident DIY homeowners. Most people complete the job in under an hour. When you're ready to install, remember to lay the dishwasher on its side on a protective surface and secure any loose components first. This prevents parts from shifting during the replacement and protects your kitchen flooring. Before ordering, please verify your dishwasher's E-Nr model number matches this part's compatibility. You'll find this number on the rating plate inside the door edge. Confirming this detail ensures you receive exactly the right component for your AEG dishwasher.
Compatible with 11 models
Crossbar, Front, Upper, 60cm
OEM: 1171564873
If your AEG dishwasher's upper basket has become unstable, wobbles during operation, or won't roll smoothly in and out, a worn or damaged front crossbar could be the culprit. This essential component supports the upper basket assembly and allows it to glide freely during the wash cycle. When it fails through general wear and tear, your dishwasher becomes difficult to load and unload, and the basket may not sit properly during washing. Replacing this crossbar is a straightforward task, rated at difficulty level 2, making it ideal for confident DIY homeowners. The OEM reference 1171564873 ensures you're getting the exact part designed for your machine. When installing, take a moment to check that the basket wheels are clean and properly aligned with the new crossbar before sliding it fully into position. This simple step prevents future issues and ensures smooth operation. This part is compatible with AEG dishwashers, though you'll need to verify your specific model's E-Nr number before ordering to guarantee compatibility with your appliance.
Compatible with 11 models
Dishwasher Side Panel Rivet Clip
OEM: 1174277002
If your AEG dishwasher's side panel is loose, rattling, or separating from the main body, this rivet clip is likely your solution. Over time, the clips that secure the side panels can wear out or break due to constant opening and closing, leaving your appliance looking shabby and potentially exposing internal components. This genuine OEM replacement part (reference 1174277002) restores the panel to its proper position and keeps everything secure. Installation is straightforward, rated at difficulty level 2, so most confident DIY homeowners can tackle it without professional help. When fitting the clip, ensure the side panel is properly aligned with the dishwasher body before fully tightening. This prevents unnecessary strain on the clip and guarantees a flush fit. Take your time during this step and you'll achieve a professional-looking result that lasts. Before ordering, verify your dishwasher's E-Nr model number, which you'll find on the rating plate inside the door edge. This ensures complete compatibility with your specific AEG model and prevents any installation issues.
Compatible with 11 models
Screw,
OEM: 140185353012
Is your AEG dishwasher sitting unevenly or wobbling during its cycle? Loose or corroded screws in the feet housing are often the culprit, causing your appliance to shift and operate inefficiently. This genuine replacement screw (OEM reference 140185353012) restores stability to your dishwasher's base, eliminating annoying vibrations and ensuring it sits perfectly level on your kitchen floor. Wear and general failure of these fasteners happens naturally over time as your dishwasher vibrates through thousands of wash cycles. Fortunately, this is a straightforward fix that most DIY homeowners can tackle in under an hour. The installation difficulty is rated 2 out of 10, making it one of the more accessible repairs. When fitting the new screw, use a slightly longer socket wrench rather than a standard screwdriver to ensure you don't accidentally strip the housing. This gives you better leverage and control in the tight space beneath your dishwasher. Before ordering, please verify your appliance's E-Nr model number against our compatibility list to guarantee this is the correct part for your AEG dishwasher.
Compatible with 11 models
Adjustable Dishwasher Foot
OEM: 1520664101
If your AEG dishwasher has become unstable, noisy during cycles, or is sitting unevenly on your kitchen floor, a worn or damaged foot is likely the culprit. Over time, these adjustable feet can deteriorate through normal use, causing your appliance to rock or vibrate excessively. Replacing the faulty foot will restore stability and prevent potential damage to surrounding units. This genuine adjustable dishwasher foot, reference 1520664101, is designed specifically for AEG models and provides the levelling adjustment you need for a perfectly balanced installation. The repair is straightforward, rated at difficulty level 2, so most confident DIY homeowners can tackle it without professional help. When installing your new foot, remember to adjust the height carefully after fitting to ensure your dishwasher sits completely level. This small step prevents future vibration problems and extends the life of your appliance. Stock this genuine replacement part with confidence, knowing it's manufactured to OEM standards. Before ordering, please verify your dishwasher's E-Nr model number matches our compatibility list to ensure you receive the correct component.
Compatible with 10 models
Adjustable Foot, M8x48mm
OEM: 8075188014
If your AEG dishwasher is sitting unevenly or wobbling during the wash cycle, a worn or damaged adjustable foot is likely the culprit. Over time, these levelling feet wear down through normal use, causing your appliance to become unstable and potentially noisy during operation. This genuine OEM adjustable foot (reference 8075188014) restores proper balance to your dishwasher, eliminating vibration and ensuring it sits flush against your kitchen units. Replacing it is straightforward—rated as difficulty level 2—making it an ideal DIY job for most homeowners. Installation simply requires turning the foot anti-clockwise to remove the old one, then screwing the new foot into place and adjusting the height using the locking nut. A helpful tip: adjust all four feet evenly to maintain proper balance, checking with a spirit level as you go. This part addresses general wear and failure that naturally occurs with age. Before ordering, verify your dishwasher's E-Nr model number against our compatibility list to ensure this is the correct replacement for your specific AEG model.
Compatible with 10 models
Dishwasher Plinth Holder
OEM: 1170156036
If your AEG dishwasher is looking unstable or wobbling when you open the door, the plinth holder is likely worn out or damaged. This component supports the protective plinth panel at the base of your machine, and when it fails, the entire lower front can become loose or misaligned. The good news is that replacing this part is straightforward and well within the capabilities of most home DIYers. The OEM reference number 1170156036 will help you identify the correct replacement for your model. Installation difficulty is rated at level 2, meaning you'll need just basic tools and about 30 minutes of your time. Before you start, make sure your dishwasher is unplugged from the electricity supply for safety. A handy tip: take a photo of the old holder before removal so you can see exactly how it clips into place, making the refitting process much simpler. This part addresses general wear and failure, which commonly occurs over time through regular use and the constant vibration of the wash cycle. Before ordering, please verify your dishwasher's E-Nr model number to ensure complete compatibility.
Compatible with 10 models
Bridge, Lower Basket, Left
OEM: 140114626017
If your dishwasher's lower basket is sitting at an awkward angle or won't slide smoothly, a worn or broken bridge support could be the culprit. This component keeps your basket level and stable during the wash cycle, so when it fails, you'll notice dishes rattling around or the basket becoming difficult to remove. The lower basket bridge (OEM reference 140114626017) is a straightforward replacement that takes just minutes to fit. This is a genuine AEG part designed to restore your dishwasher's performance after general wear and failure over time. Installation difficulty is rated at level 2, meaning most confident DIYers can handle it without specialist tools. Our practical tip: before you start, empty the dishwasher completely and ensure it's switched off at the wall. Take a photo of how the old bridge sits before removing it, so you'll know exactly how to position the new one. This part is compatible with AEG dishwashers, but always verify your machine's E-Nr model number before ordering to guarantee compatibility with your specific model.
Compatible with 8 models
Bridge, Lower Basket, Right
OEM: 140114626025
If your dishwasher's lower basket is sagging, won't slide smoothly, or sits at an awkward angle, a worn or broken bridge support is likely the culprit. This right-side bridge component, referenced as 140114626025, provides essential structural support to keep your basket level and functioning properly during wash cycles. Over time, the mounting points on this part can weaken through general wear, causing the basket to become unstable. Replacing it restores proper alignment and smooth operation, making loading and unloading far easier. Installation is straightforward, rated at difficulty level 2, meaning most confident DIY homeowners can manage it without specialist tools. A practical tip: before removing the old part, take a photograph of how it connects to help guide reassembly. You'll typically need just a screwdriver and perhaps a small wrench. This genuine AEG spare part ensures compatibility and longevity. However, before ordering, verify your dishwasher's E-Nr model number matches our compatibility list, as this guarantees correct fitment for your specific machine.
Compatible with 8 models
Dishwasher Top Fixing Bracket
OEM: 1172870014
Is your AEG dishwasher sitting unevenly or wobbling during operation? A worn or damaged top fixing bracket could be the culprit. This component secures the upper section of your dishwasher to the cabinet, and when it fails, your appliance loses stability, creating noise and potential safety issues. The genuine OEM part 1172870014 is designed specifically for AEG models and provides the robust support your dishwasher needs. Replacing it is a straightforward job rated at difficulty level 2, making it manageable for most DIY homeowners without specialist knowledge. When installing your new bracket, remember to fully disconnect the dishwasher from the power supply first, then carefully remove the side panel to access the mounting points. Take a photo before disassembly so you can easily reference the correct positioning during reassembly. General wear and failure are common reasons for bracket replacement, especially in busy households where the dishwasher operates frequently. This genuine part will restore your appliance's stability and quietness. Before ordering, please verify your dishwasher's E-Nr model number matches our compatibility list, as this ensures you receive the correct bracket for your specific model.
Compatible with 8 models
Rail, Cutlery Tray, Left,
OEM: 140129501098
If your dishwasher cutlery basket isn't sitting properly or the tray is sagging to one side, a worn left-hand rail could be the culprit. Over time, these plastic guides deteriorate from regular use and exposure to moisture, causing your cutlery tray to misalign or fail to slide smoothly. This original AEG spare part (reference 140129501098) restores proper positioning and operation. Replacing this component is straightforward for most DIY homeowners, rated at difficulty level 2. You'll simply need to remove the old rail from its housing and slide the new one into place. A helpful tip: before installation, check that the mounting clips are clean and free from debris, as any obstruction can prevent proper seating and cause the same problems to recur. This genuine part ensures perfect compatibility with your AEG dishwasher and maintains the precision engineering that keeps everything running smoothly. Most installations take less than thirty minutes with just basic tools. Before ordering, please verify your appliance's E-Nr model number matches our compatibility list to guarantee this is the correct part for your machine.
Compatible with 8 models
Rail, Cutlery Tray, Right,
OEM: 140129501106
A worn or broken cutlery tray rail stops your dishwasher from working properly, leaving you unable to clean your dishes effectively. If your AEG dishwasher's cutlery basket isn't sliding smoothly or keeps jamming, this right-hand rail is likely the culprit after years of regular use. This genuine replacement rail (OEM reference 140129501106) restores smooth operation to your cutlery tray, allowing it to glide in and out without resistance. Installation is straightforward, rated at difficulty level 2, so most DIY homeowners can handle it without calling an engineer. When fitting the new rail, ensure you fully disengage the old one from both the upper and lower mounting points before sliding it free. This prevents accidental damage to surrounding components and makes reinstallation much easier. This part addresses general wear and failure issues that naturally develop over time. It's a cost-effective solution that extends your dishwasher's lifespan considerably. Before ordering, please verify your AEG dishwasher's E-Nr model number against our compatibility list to ensure this is the correct part for your appliance.
Compatible with 8 models
Crossbar, Front, Bottom,
OEM: 1173922004
If your AEG dishwasher is showing signs of wear or instability, a damaged front bottom crossbar could be the culprit. This component supports the lower rack assembly and helps maintain proper alignment during the wash cycle. When it fails, you may notice the rack sitting unevenly or difficulty loading and unloading dishes. This genuine OEM crossbar (reference 1173922004) is a straightforward replacement that most competent DIY homeowners can tackle. The installation difficulty rating of 2 means you'll need basic tools and some mechanical confidence, but nothing too demanding. Our top tip: before you start, take a photograph of the existing part in position so you can reference the correct orientation during reassembly. The crossbar is essential for maintaining your dishwasher's structural integrity and ensuring smooth operation. Replacing worn components promptly prevents further damage to surrounding parts. Before ordering, please verify your dishwasher's E-Nr model number matches our compatibility list. You'll find this on the appliance's data plate, usually located inside the door frame. This ensures you receive the correct part first time.
Compatible with 7 models
Dishwasher Side Trim
OEM: 1522222635
If your AEG dishwasher looks a bit shabby around the edges or the side trim has come loose, this replacement part will restore it to looking like new. The side trim houses the feet and provides a neat finish to your appliance, so when it starts to wear or fail, it really shows. This genuine OEM side trim (reference 1522222635) is designed specifically for AEG dishwashers and slots into place straightforwardly. With an installation difficulty rating of just 2 out of 10, most DIY homeowners can manage this repair in under an hour without specialist tools. When you're fitting the new trim, take a moment to clean the mounting area thoroughly first. Any dust or debris left behind can prevent a snug fit, which defeats the purpose of replacing it. Once clean, the trim should slide into position with minimal fuss. Before ordering, do verify your dishwasher's E-Nr model number matches this part's compatibility. You'll find this number on the data plate inside your machine. Getting the right part first time saves time and frustration when you're ready to get that dishwasher looking pristine again.
Compatible with 7 models
Mounting Kit, Fully Integrated
OEM: 140125033344
If your AEG dishwasher is sitting unevenly or wobbling during its cycle, the mounting kit may be the culprit. Over time, the feet and housing components that support your appliance can wear down or fail, causing instability and potentially damaging your kitchen cabinet or worktop. This genuine OEM mounting kit (reference 140125033344) restores proper support and stability to your dishwasher. The fully integrated design means all necessary components are included, so you won't need to source parts separately. Installation is straightforward, rated at difficulty level 2, making it suitable for most competent DIY homeowners. When fitting the new kit, ensure your dishwasher is completely empty and disconnected from the water supply beforehand. Take a photograph of the original mounting points before removal—this simple step helps enormously when aligning the new components correctly. The job typically takes under an hour and requires only basic tools. Once installed, your dishwasher should sit level and operate smoothly without vibration. Before ordering, please verify your appliance's E-Nr model number matches our compatibility information. You'll find this on the sticker inside your dishwasher door.
Compatible with 7 models
Mounting Kit, Sliding Type
OEM: 8079527498
If your AEG dishwasher is sitting unevenly, wobbling during cycles, or the door won't close properly, the mounting kit may have failed due to general wear. This sliding type mounting kit (OEM reference 8079527498) secures your dishwasher to the underside of your worktop, keeping it stable and level throughout its wash cycles. Replacing this component is straightforward and rated as difficulty level 2, making it an ideal DIY job for most homeowners. You'll need just basic tools and roughly 30 minutes to complete the installation. Here's a practical tip: before fitting the new kit, take a moment to clean away any debris or old adhesive from the mounting area. This ensures a secure, lasting installation and prevents future alignment issues. The mounting kit houses the feet mechanisms that allow your dishwasher to slide smoothly into place under your worktop, so getting this right is essential for proper operation and longevity. Please verify your appliance's E-Nr model number before ordering to ensure complete compatibility with your specific AEG dishwasher model.
Compatible with 7 models
Adjustable Dishwasher Foot
OEM: 1521870012
If your AEG dishwasher is sitting unevenly or wobbling during operation, worn or damaged feet are likely the culprit. Over time, these support feet can deteriorate through general wear, causing your appliance to become unstable. This not only sounds unpleasant but can also affect performance and create safety concerns in your kitchen. The adjustable dishwasher foot (OEM reference 1521870012) is a straightforward replacement that restores proper levelling and stability to your machine. Installation difficulty is rated at just 2 out of 10, making this an achievable DIY job for most homeowners without specialist knowledge. When installing, remember to adjust all four feet evenly once fitted. This ensures your dishwasher sits completely level, which is essential for the door to close properly and the appliance to function optimally. You'll need a spirit level to get this right, but it only takes a few minutes. Before ordering, please verify your dishwasher's E-Nr model number to confirm compatibility. You'll find this on the rating plate inside the door edge, and it's crucial for ensuring this part will fit your specific AEG model.
Compatible with 6 models
Adjustable Front Dishwasher Foot
OEM: 1527992026
If your AEG dishwasher is sitting unevenly or wobbling during the wash cycle, a worn or damaged front foot is likely the culprit. Over time, these adjustable feet can wear down or fail, causing your appliance to become unstable and potentially leading to noise and vibration problems. This genuine adjustable front dishwasher foot (OEM reference 1527992026) is a straightforward replacement that restores proper levelling and stability to your machine. The foot features an adjustable design, allowing you to fine-tune the height once installed to ensure your dishwasher sits perfectly level on your kitchen floor. Installation is straightforward, rated at difficulty level 2, making it an achievable task for most DIY homeowners. A helpful tip: before you begin, place a spirit level on top of your dishwasher to identify which foot needs adjustment, then work methodically to avoid creating new imbalances. This is an essential maintenance part that prevents further damage to your appliance and restores safe, quiet operation. Before ordering, please verify your dishwasher's E-Nr model number matches our compatibility information to ensure this is the correct part for your machine.
Compatible with 6 models
Mounting Kit,
OEM: 140125033591
If your AEG dishwasher is sitting unevenly or wobbling during operation, worn feet or a damaged housing could be the culprit. This mounting kit restores stability and prevents further damage to your appliance and kitchen units. Over time, the feet and housing components naturally wear down through regular use, causing your dishwasher to shift or rock. This original equipment mounting kit (OEM reference 140125033591) is designed to replace these worn parts and get your machine sitting level again. Installation is straightforward, rated at difficulty level 2, making it suitable for confident DIY homeowners. When fitting the new mounting kit, ensure your dishwasher is completely empty and turned off at the mains. It's helpful to have someone steady the appliance whilst you work underneath, as you'll need to access the feet from below the unit. This genuine part guarantees compatibility and durability. Before ordering, please verify your dishwasher's E-Nr model number, which you'll find on the rating plate inside the door edge. This ensures you're getting the correct mounting kit for your specific AEG model.
Compatible with 5 models
Plinth Reinforcement,front,bottom
OEM: 1527255044
When your AEG dishwasher's base becomes unstable or wobbles during operation, a worn plinth reinforcement is often the culprit. This component supports the front bottom section of your dishwasher's housing, and over time general wear can cause it to fail, compromising the appliance's structural integrity and potentially leading to further damage. Replacing the plinth reinforcement (OEM reference 1527255044) is a straightforward DIY job rated at difficulty level 2, making it manageable for most homeowners. The part sits beneath your dishwasher, providing essential support to the cabinet frame. Before starting the installation, ensure you've switched off the power at the mains and drained any residual water from the appliance. This simple precaution takes only a few minutes but significantly improves safety during the repair. The actual replacement involves removing a few fasteners and sliding the old component out before fitting the new one into place. This genuine OEM part guarantees proper fit and reliability for your AEG dishwasher. Always verify your appliance's E-Nr model number before ordering to ensure complete compatibility with your specific model.
Compatible with 5 models
Hook, Upper Basket, Dispenser
OEM: 140018976013
# Hook, Upper Basket, Dispenser Is your Zanussi dishwasher's upper basket sitting awkwardly or not closing properly? A worn or damaged dispenser hook could be the culprit. Over time, this small but essential component deteriorates through regular use, causing the basket to become misaligned or unstable during the wash cycle. This genuine upper basket dispenser hook (OEM reference 140018976013) is a straightforward replacement that restores your dishwasher's functionality. With an installation difficulty rating of just 2, most competent DIY homeowners can manage this repair in under an hour using basic tools. When fitting the new hook, remember to fully engage the locking mechanism before sliding the basket back into position. This simple step prevents the hook from slipping during operation and ensures a secure fit that will last for years to come. Before ordering, verify that your Zanussi dishwasher's E-Nr model number matches this part's compatibility. You'll find this reference number on the appliance's data plate, usually located inside the door frame. Checking this detail takes just a moment and guarantees you receive the correct component for your machine.
Compatible with 4 models
Mounting Kit, Built-in,
OEM: 140125033658
If your AEG dishwasher is sitting unevenly or has become loose under your worktop, a worn or damaged mounting kit is likely the culprit. Over time, the feet and housing that secure your appliance can deteriorate through general wear, causing instability and potentially damaging your kitchen cabinetry. Replacing this component will restore proper alignment and stability to your dishwasher. This genuine mounting kit (OEM reference 140125033658) is designed specifically for AEG built-in dishwashers and provides a straightforward fix for most homeowners. The installation difficulty rating of 2 means you'll need basic DIY skills and a few standard tools, though many find the job manageable over an afternoon. When fitting the new kit, ensure you've fully emptied your dishwasher and have adequate space to work underneath. This makes accessing the mounting points considerably easier and safer. Before ordering, verify your dishwasher's E-Nr model number matches our compatibility list. You'll find this on the data plate inside the door frame. This simple check prevents unnecessary returns and ensures you receive the correct part for your machine.
Compatible with 3 models
Mounting Kit, Fully Integrated
OEM: 140125033245
# Mounting Kit, Fully Integrated If your dishwasher is sitting unevenly or wobbling during operation, the mounting kit is likely what you need. This component secures the appliance to its housing and keeps everything stable, preventing movement that can damage pipes and electrical connections over time. This genuine mounting kit (OEM reference 140125033245) is designed for Electrolux and Zanussi dishwashers and addresses general wear and failure of the feet housing assembly. As your dishwasher ages, these mounts can deteriorate, causing the unit to shift and creating annoying vibrations during the wash cycle. Installation is straightforward, rated at difficulty level 2, so most confident DIY homeowners can manage it without professional help. When fitting the new kit, ensure all mounting bolts are tightened evenly in a cross pattern—this prevents the appliance from sitting at an angle, which can cause problems with water drainage. The job typically takes under an hour and requires only basic tools. Once installed, your dishwasher should run smoothly without movement or noise. Before ordering, please verify your dishwasher's E-Nr model number matches this part's compatibility to ensure it's the correct replacement for your machine.
Compatible with 3 models
Plinth, White
OEM: 8070407039
Is your AEG dishwasher looking a bit shabby around the bottom, or has the plinth become loose and unstable? General wear and tear can damage the housing that protects the base of your appliance, compromising both its appearance and structural integrity. A worn plinth not only looks unsightly but can also expose internal components to dust and moisture. This genuine white plinth (OEM reference 8070407039) is the perfect replacement to restore your dishwasher to its original condition. Installation is straightforward and rates just 2 out of 5 for difficulty, making it an ideal project for confident DIY homeowners. Before you start, ensure you've switched off the power supply and have adequate space to work underneath the appliance. A helpful tip: place wooden blocks under the dishwasher frame to support it safely whilst you remove and fit the new plinth. The whole job typically takes under an hour, and you'll immediately notice the difference in your kitchen's appearance. Please verify your dishwasher's E-Nr model number against our compatibility list before ordering to guarantee you receive the correct part.
Compatible with 3 models
Work Top, White
OEM: 140132016019
If your dishwasher isn't sitting level or the feet seem worn and unstable, a damaged work top housing is likely the culprit. This white work top component supports your AEG dishwasher and keeps it properly positioned under your kitchen counter. Over time, the feet housing can wear down or crack from general use, causing your appliance to shift or wobble during operation. Replacing it restores stability and prevents potential damage to your kitchen cabinetry and plumbing connections. This is a straightforward repair rated at difficulty level 2, making it ideal for confident DIY homeowners. When installing your new work top, remember to support the dishwasher from above with a jack or helper before removing the old housing. This prevents unnecessary strain on the internal components and makes the job considerably easier. The OEM reference 140132016019 ensures you're getting the exact part designed for your machine. Before placing your order, please verify your dishwasher's E-Nr model number matches our compatibility list, as this guarantees a perfect fit for your AEG appliance.
Compatible with 3 models
Work Top, White, Flat
OEM: 140132016035
When your dishwasher's worktop becomes cracked, warped, or worn from years of daily use, it not only looks unsightly but can also affect the appliance's stability and performance. This genuine AEG white flat worktop (OEM reference 140132016035) is the perfect replacement to restore your dishwasher to like-new condition. Designed specifically for AEG dishwashers, this part addresses general wear and failure that occurs naturally over time. Installation is straightforward, rated at difficulty level 2, making it an ideal DIY project for most homeowners. Simply ensure you've switched off the power at the mains before beginning work, and take a photograph of the existing setup so you can reference it during reassembly. The white finish seamlessly integrates with standard kitchen designs, providing a clean, professional appearance once installed. By replacing a damaged worktop early, you'll prevent further deterioration and maintain proper dishwasher alignment within your fitted kitchen. Before ordering, please verify your appliance's E-Nr model number matches this part's compatibility requirements. This simple check ensures you receive the correct component for a hassle-free installation.
Compatible with 3 models
Mounting Kit, Built-in,
OEM: 140125033609
If your AEG dishwasher is sitting unevenly or wobbling during operation, the mounting kit may be worn out and need replacing. Over time, the feet and housing components experience general wear that compromises stability and can lead to noise or movement during the wash cycle. This genuine OEM mounting kit (reference 140125033609) restores proper support and alignment to your built-in dishwasher. Installation is straightforward, rated at difficulty level 2, making it suitable for most confident DIY homeowners. The job typically takes under an hour with basic tools. When fitting the new mounting kit, remember to fully unload your dishwasher and ensure the appliance is isolated from power before starting work. This simple precaution keeps you safe and prevents accidental activation during installation. Once fitted, your dishwasher should operate smoothly without vibration or movement, restoring both stability and peace of mind during every wash cycle. Before ordering, please verify your appliance's E-Nr model number to ensure complete compatibility with this part.
Compatible with 2 models
Mounting Kit, Fully Integrated,
OEM: 140125033351
Is your AEG dishwasher sitting unevenly or wobbling during the wash cycle? A worn or damaged mounting kit could be the culprit. Over time, the feet housing deteriorates through general wear and failure, causing your appliance to lose stability and potentially leading to further damage if left unaddressed. This fully integrated mounting kit restores proper support and balance to your dishwasher, eliminating annoying vibrations and ensuring safe, secure operation. The OEM reference 140125033351 guarantees exact compatibility with your AEG model, so you can be confident you're getting the right part first time. Installation is straightforward, rated at difficulty level 2, making this an ideal DIY project for most homeowners. When fitting the new kit, ensure you've fully drained the dishwasher and have adequate workspace underneath—this simple preparation step makes the job considerably quicker and easier. Before ordering, please verify your appliance's E-Nr model number matches the compatibility details listed, as this ensures perfect fitment and performance. With this replacement, your dishwasher will run smoothly and quietly once more.
Compatible with 2 models
Plinth, Grey
OEM: 1173682012
Is your AEG dishwasher looking shabby or sitting unevenly on your kitchen floor? A worn or damaged plinth housing could be the culprit. This grey plinth covers the feet area of your dishwasher, protecting vital components whilst maintaining a neat appearance. Over time, general wear and tear can cause the plinth to crack, discolour or fail entirely, affecting both function and aesthetics. Replacing your plinth is straightforward for most DIY homeowners, with an installation difficulty rating of just 2 out of 10. The job typically requires only basic tools and takes less than an hour to complete. Before you start, ensure you have the correct OEM reference number 1173682012 for your specific model. A helpful tip: once you've removed the old plinth, check that the mounting points are clean and free from debris before fitting the new one. This ensures a secure, flush finish. Always verify your dishwasher's E-Nr model number before ordering to guarantee compatibility with your AEG appliance. You'll find this number on the inside edge of the door or in your user manual.
Compatible with 2 models
Plinth, Inox
OEM: 8070407013
# Plinth, Inox If your Zanussi dishwasher is looking shabby or the base housing has deteriorated through everyday use, a worn plinth is likely the culprit. This stainless steel plinth (OEM reference 8070407013) restores your appliance's appearance and replaces the protective base housing that shields the feet and lower mechanisms from dust and debris. Over time, the plinth can suffer general wear and failure, becoming discoloured, dented, or damaged. Replacing it is a straightforward solution that takes just a few minutes and requires no specialist tools. Installation is rated at difficulty level 2, making it perfectly manageable for most DIY homeowners. When fitting the new part, simply slide it into position from the bottom front of the dishwasher, ensuring it clicks firmly into place. A practical tip: gently rock the plinth side to side once installed to confirm it's seated properly and won't rattle during operation. Before ordering, verify your dishwasher's E-Nr model number matches this part's compatibility. You'll find this on the appliance's data plate, usually inside the door edge or on the side panel.
Compatible with 2 models
Spacer Strip,adhesive Tape,4 Pcs.
OEM: 140003555616
If your AEG dishwasher isn't sitting level or you've noticed gaps appearing around the base, worn spacer strips are likely the culprit. These adhesive tape strips maintain proper spacing between your dishwasher and its housing, preventing movement and damage over time. General wear eventually causes them to deteriorate, compromising the appliance's stability and alignment. This genuine AEG replacement set contains four spacer strips (OEM reference 140003555616) designed to restore your dishwasher to factory specifications. Installation is straightforward, rated at difficulty level 2, making it an ideal DIY job for most homeowners. Simply clean the mounting surface thoroughly before applying the new adhesive strips—this ensures maximum adhesion and longevity. The whole job typically takes under thirty minutes and requires no special tools. Once installed, you'll notice improved stability and eliminate those annoying wobbles during the wash cycle. Before ordering, please verify your dishwasher's E-Nr model number matches this part's compatibility. You'll find this number on the rating plate inside your appliance, usually on the door edge or side panel. This confirms you're purchasing the correct replacement for your specific model.
Compatible with 2 models
Stiffening, Holder, Roller, Top
OEM: 140002047011
Is your AEG dishwasher developing movement or noise issues? The stiffening holder roller top part may be what you need. Over time, this component experiences general wear and failure, which can affect the stability of your dishwasher's internal mechanisms and lead to frustrating rattling sounds during operation. This genuine OEM spare part, reference 140002047011, is designed to restore proper support and alignment within your appliance. Replacing it is straightforward enough for a confident DIY homeowner, with an installation difficulty rating of just 2 out of 5. You'll find the job manageable if you're comfortable working with basic tools and following instructions carefully. When fitting this part, take a moment to ensure all surrounding components are clean and free from debris before reinstalling. This simple step prevents premature wear on your new part and helps everything sit properly. Before placing your order, please verify the E-Nr model number on your AEG dishwasher to confirm this part is compatible. You'll typically find this number on a sticker inside the door edge or on the appliance's documentation.
Compatible with 2 models
Work Top, Inox
OEM: 140132016027
# Zanussi Dishwasher Inox Work Top Is your dishwasher sitting unevenly or wobbling on the floor? A worn or damaged work top housing could be the culprit. Over time, the feet housing that supports your appliance can deteriorate through general wear, causing instability and potential damage to your kitchen units. This genuine Zanussi inox work top (OEM reference 140132016027) is a straightforward replacement that restores proper levelling and stability to your dishwasher. Installation difficulty is rated at just 2 out of 10, making it an achievable DIY job for most homeowners. When fitting the new work top, ensure your dishwasher is completely empty and unplugged from the mains. You'll need to tilt or partially pull out the appliance to access the feet housing underneath, so clear sufficient space in your kitchen beforehand. This simple precaution prevents accidents and makes the job considerably easier. Before placing your order, verify the E-Nr model number on your dishwasher's documentation or the appliance itself to confirm compatibility. This ensures you receive the correct part for your specific Zanussi model.
Compatible with 2 models
Basket Tines, L=271mm
OEM: 140022277010
Broken or worn basket tines are one of the most common reasons your AEG dishwasher stops holding dishes securely. Over time, these plastic supports crack, split, or snap completely, leaving your crockery loose and prone to damage during the wash cycle. If your baskets feel unstable or dishes won't stay in place, replacing these tines will restore proper functionality. This genuine replacement part, reference 140022277010, is designed for AEG dishwashers and measures 271mm in length. Installation difficulty is rated at level 2, making it manageable for most DIY homeowners with basic tools and patience. The job typically involves removing your lower basket, locating the damaged tines, and sliding the new ones into position. A helpful tip: before installation, run your empty dishwasher briefly on a hot cycle to soften any stuck plastic, making removal easier. Ordering the correct part is straightforward, but do verify your appliance's E-Nr model number before purchasing. You'll find this on the dishwasher's interior wall or documentation. Matching this number ensures perfect compatibility and saves unnecessary returns.
Compatible with 1 model
Cup Shelf, with Rubber, Grey
OEM: 140000450068
When your AEG dishwasher's cup shelf becomes worn, cracked, or fails to hold items securely, it's time for a replacement. This grey cup shelf with rubber fittings restores proper functionality to your appliance, ensuring your dishes and cups are safely supported during the wash cycle. This genuine OEM part (reference 140000450068) is specifically designed for AEG dishwashers and comes ready to install. General wear and failure are common issues with shelving components, particularly if your dishwasher is heavily used or getting on in years. Installation is straightforward, rated at difficulty level 2, making this a manageable DIY job for most homeowners. Before you begin, take a photograph of how the existing shelf is positioned, as this will guide you when fitting the new component. Simply remove the old shelf by unclipping or unscrewing it from the rails, then slide the new unit into place and secure it firmly. Please verify your dishwasher's E-Nr model number matches our compatibility information before ordering, as this ensures you receive the correct part for your specific AEG model.
Compatible with 1 model
Mounting Kit, Esl75320lo
OEM: 140125033047
If your AEG dishwasher is sitting unevenly or wobbling during operation, a worn or damaged mounting kit could be the culprit. Over time, the feet and housing that support your appliance can deteriorate through everyday use, causing instability and annoying vibrations. Replacing the mounting kit is a straightforward solution that restores proper levelling and performance. This genuine AEG spare part, referenced as 140125033047, is designed specifically for compatible AEG dishwasher models and handles general wear and failure with ease. Installation difficulty sits at level 2, making it manageable for most DIY homeowners with basic tools and a little patience. When fitting the new mounting kit, ensure you've fully emptied your dishwasher and have adequate workspace underneath. Take time to adjust each foot carefully for perfect balance, as this prevents future movement and noise during the wash cycle. Before ordering, please verify your dishwasher's E-Nr model number against the compatibility list. This ensures you receive the correct part first time and avoid unnecessary delays to your repair.
Compatible with 1 model
Plinth, Grey
OEM: 1173372226
If your AEG dishwasher looks shabby or unstable, a worn or damaged plinth could be the culprit. This grey base panel protects the underside of your appliance whilst giving it a finished appearance, and over time it can crack, discolour, or deteriorate from general wear and tear. Replacing the plinth is straightforward work for any confident DIYer. The part (OEM reference 1173372226) has a difficulty rating of just 2 out of 10, meaning most people can manage the replacement in under an hour with basic tools. Start by securing the dishwasher in place to prevent it from tipping forwards when you remove the old plinth, then carefully unclip or unscrew the damaged section and slide the new grey plinth into position. This replacement will restore your dishwasher's appearance and ensure the base remains properly protected against dust and debris. It's a cost-effective way to extend your appliance's life without calling out an engineer. Before ordering, please verify your dishwasher's E-Nr model number matches this part's compatibility. You'll find this number on the appliance's rating label, usually inside the door or on the side panel.
Compatible with 1 model
Plinth, White
OEM: 8090496012
Your dishwasher's base has cracked or worn away, leaving it looking shabby or sitting unevenly? A damaged plinth affects both appearance and stability, so replacing it is a straightforward solution that restores your appliance to like-new condition. This genuine white plinth (OEM reference 8090496012) is designed specifically for AEG dishwashers and handles the everyday wear that comes with years of use. Installation is straightforward, rated at difficulty level 2, making it perfectly manageable for a confident DIYer with basic tools. When fitting the new plinth, ensure your dishwasher is unplugged and positioned away from the wall slightly. This gives you enough space to slide the plinth into place without straining. The part slots into the feet housing, securing your machine firmly to the floor and hiding unsightly cable runs. Before ordering, please verify your dishwasher's E-Nr model number, which you'll find on the energy label inside the door. This ensures complete compatibility and prevents any unnecessary delays. Once confirmed, this reliable replacement will have your dishwasher looking and performing like new.
Compatible with 1 model
Spring Clip, Indicator, Red
OEM: 140109196059
If your AEG dishwasher's feet housing has become loose or unstable, or the red indicator clip has worn away over time, your appliance may rock or sit unevenly during operation. This replacement spring clip restores proper support and positioning to keep your dishwasher stable and functioning correctly. This genuine OEM part, reference 140109196059, is designed specifically for AEG dishwashers and handles the everyday wear that comes with regular use. The red indicator makes it easy to identify proper installation at a glance. Installation difficulty is rated at level 2, making this a straightforward job for most DIY homeowners. When fitting the clip, ensure the feet housing is completely dry before reinstalling, and take a moment to verify that the clip sits flush against the housing to prevent future loosening. Most people complete this repair in under 15 minutes with just basic tools. Before ordering, please check your dishwasher's E-Nr model number on the appliance information plate to confirm compatibility with this part.
Compatible with 1 model
Stopper,basket Rail,front,comfortlift
OEM: 140027018039
Is your dishwasher basket sitting at an awkward angle or failing to glide smoothly? A worn or broken front basket rail stopper could be the culprit. This component keeps your basket properly aligned and supported during the wash cycle, so when it deteriorates through general wear, you'll notice the basket shifting or binding. The good news is that replacing this part is straightforward. This genuine AEG stopper (OEM reference 140027018039) is rated as a difficulty level 2 installation, meaning most confident DIY homeowners can tackle it without professional help. You'll simply need basic hand tools and around 15 minutes of your time. When you're ready to install, ensure the basket is fully removed first and take a photo of the old component before removing it. This helps you position the new stopper correctly and ensures proper basket alignment afterwards. Before ordering, please verify your dishwasher's E-Nr model number, which you'll find on the appliance rating plate inside the door edge. Confirming compatibility takes just a moment and guarantees you're purchasing the right part for your AEG model.
Compatible with 1 model
Work Top, White, 447x595mm
OEM: 8070934016
When your dishwasher's work top becomes cracked, warped or discoloured from years of use, water can seep into the appliance and cause further damage. This genuine AEG replacement work top restores a protective seal and gives your dishwasher a fresh, clean appearance. This white work top is designed to fit standard AEG dishwasher models and carries the OEM reference 8070934016 for easy identification. Measuring 447x595mm, it's a straightforward replacement that most confident DIY homeowners can tackle in under an hour, with an install difficulty rating of just 2 out of 10. Installation is straightforward, but here's a helpful tip: before removing the old work top, take a photo of how it sits in place. This reference image proves invaluable when positioning the new one, ensuring perfect alignment with your dishwasher frame and avoiding any gaps that could let moisture escape. This part addresses general wear and failure, making it ideal if your current work top shows visible damage or has become loose. Remember to verify your appliance's E-Nr model number before ordering to guarantee compatibility with your specific AEG dishwasher.
Compatible with 1 model