Spare parts category
door_parts
door_parts spare parts for Bosch and Siemens dishwashers. All 37 parts have verified OEM compatibility data.
37 parts · All OEM-verified
Supp.spray Arm Ch-d-i
OEM: 140112437029
If your AEG dishwasher isn't cleaning your dishes properly or you've noticed water spraying unevenly during the wash cycle, a worn or damaged spray arm could be the culprit. Over time, these hardworking components suffer from general wear and failure, leading to blocked nozzles or mechanical deterioration that prevents proper water distribution. This replacement spray arm (OEM reference 140112437029) restores full cleaning performance to your dishwasher, ensuring water reaches every corner of your dishes with consistent pressure. Installation is straightforward and rates as a level 2 difficulty job, making it ideal for confident DIY homeowners. The process typically takes under an hour with basic tools. A practical tip: before fitting the new arm, run a quick cycle with white vinegar to flush out any mineral deposits from your dishwasher's internal pipework. This prevents premature clogging of your fresh component. Once installed, you'll notice an immediate improvement in wash quality and efficiency. Before ordering, please verify your dishwasher's E-Nr model number matches this part's compatibility to ensure a perfect fit for your AEG appliance.
Compatible with 44 models
Screen, Sump
OEM: 140073097010
When your AEG dishwasher isn't draining properly or you've noticed water pooling at the bottom, a worn or damaged sump screen is often the culprit. This component prevents debris from blocking the drain system, and over time it can become clogged or crack from general wear and failure. Replacing your sump screen is a straightforward job that most DIY homeowners can tackle in under an hour. The part reference 140073097010 is the genuine OEM component designed specifically for AEG dishwashers, ensuring perfect compatibility and reliable performance. Installation difficulty is rated at level 2, meaning you'll need basic tools and a bit of patience, but no specialist knowledge required. Before you start, take a photo of the existing part to familiarise yourself with its position. This handy tip makes reassembly much easier. The sump screen sits in the door assembly area, filtering water before it exits the machine. Once installed, your dishwasher should drain efficiently again. Always verify your appliance's E-Nr model number before ordering to guarantee this part is compatible with your specific AEG dishwasher model.
Compatible with 39 models
Basket Rail,upper
OEM: 140101683021
Is your dishwasher's upper basket not sliding smoothly or sitting unevenly? A worn or damaged basket rail is the likely culprit. Over time, these plastic guides endure constant friction from loading and unloading your dishes, eventually becoming brittle or cracked. Replacing the upper basket rail restores proper alignment and effortless movement, making your daily washing routine hassle-free again. This genuine AEG spare part, reference 140101683021, is designed to fit perfectly with your dishwasher's existing components. Installation difficulty is rated at 2, meaning most DIY homeowners can tackle this repair without specialist knowledge or tools. The straightforward process typically involves removing the upper basket, unclipping the old rail, and sliding the new one into place. One practical tip: before removing the old rail, take a photo of how it sits in position. This simple reference prevents any confusion during reinstallation and ensures correct alignment when you fit the replacement. Please verify your dishwasher's E-Nr model number against the product compatibility information before ordering. This ensures you receive the correct part for your specific AEG model.
Compatible with 33 models
Latch, Door,
OEM: 140035300114
If your AEG dishwasher door won't close properly or keeps popping open during the wash cycle, a worn or broken door latch is likely the culprit. Over time, the latch mechanism experiences general wear and failure, compromising the seal needed for your appliance to function correctly. This essential component ensures the door stays firmly shut throughout the cycle, maintaining water pressure and temperature. The genuine AEG replacement latch, reference 140035300114, is designed to restore your dishwasher to full working order. Installation is straightforward, rated at difficulty level 2, meaning most DIY homeowners can tackle this repair confidently without specialist knowledge. When fitting your new latch, take care to align the mounting brackets carefully before securing them fully. This ensures smooth operation and prevents future problems. The component should click into place with a satisfying snap when properly installed. Before placing your order, please verify your dishwasher's E-Nr model number, as compatibility can vary across different AEG models. You'll find this number on your appliance's data plate, usually located inside the door edge or on the side wall.
Compatible with 33 models
Slider, Sliding Panel, Plastic
OEM: 1174143014
If your dishwasher door isn't gliding smoothly or feels stiff when opening and closing, a worn plastic slider could be the culprit. Over time, these small but essential components wear down through repeated use, causing friction and difficulty operating your appliance. This genuine AEG replacement slider (OEM reference 1174143014) restores smooth door operation and prevents further damage to your dishwasher's hinges and frame. It's a straightforward fix rated at difficulty level 2, making it ideal for confident DIY homeowners tackling basic appliance repairs. Before installing, take a moment to clean away any debris or hardened detergent residue from the door track. This simple step ensures your new slider seats properly and functions smoothly from day one, potentially extending its lifespan significantly. The repair typically takes 10-15 minutes with basic tools. Most users find the slider clips securely into place without complications. Please verify your dishwasher's E-Nr model number matches our compatibility information before ordering. You'll find this on the manufacturer's plate inside your appliance.
Compatible with 27 models
Lower Spray Arm,support,dark G
OEM: 1119158176
If your AEG dishwasher isn't cleaning dishes properly or you've noticed water spraying unevenly during cycles, a worn lower spray arm support could be the culprit. Over time, this component can deteriorate through normal use, causing the spray arm to sit incorrectly or fail to rotate smoothly. This part (OEM reference 1119158176) is the exact replacement you need to restore your dishwasher's cleaning performance. Installation is straightforward and falls into our difficulty level 2 category, making it manageable for most DIY homeowners. You'll typically need just a few basic tools. A helpful tip is to place a towel or shallow tray underneath whilst removing the old support, as residual water may still be present in the appliance. The replacement process usually takes under an hour and will save you money compared to calling out an engineer. Once fitted, you should notice immediate improvements in wash quality and cycle efficiency. Before placing your order, please verify the E-Nr model number on your AEG dishwasher to ensure this part is compatible with your specific machine.
Compatible with 26 models
Left Side Panel, Zinc-plated, 519x808mm
OEM: 8581904030500
When your dishwasher's left side panel shows signs of rust, dents or general deterioration, it's time for a replacement. This zinc-plated panel protects the internal mechanisms whilst maintaining the appearance of your appliance, and wear over time is completely normal with regular use. This genuine OEM part (reference 8581904030500) is designed specifically for AEG dishwashers and measures 519x808mm. The zinc coating resists corrosion effectively, ensuring your replacement will last for years to come. Installation is straightforward at difficulty level 2, making this an ideal DIY job for homeowners. Before you begin, ensure the dishwasher is disconnected from the power supply. The panel typically secures with a few bolts along the top and side edges, which you'll remove using a standard socket set. Take a photo of the original position before dismantling, as this provides a helpful reference when fitting the new panel. Always verify your dishwasher's E-Nr model number before ordering. This unique identifier ensures perfect compatibility with your specific appliance, preventing any installation issues or returns.
Compatible with 22 models
Door Lock, Casing, with Opener 60n
OEM: 4055973491
If your AEG dishwasher door won't latch properly or keeps popping open during the wash cycle, the door lock mechanism may have worn out or failed. This genuine OEM part (reference 4055973491) is the complete door lock casing assembly with integrated opener, designed to restore secure closure and reliable operation to your appliance. Over time, the latch mechanism experiences repeated stress from daily use, and the plastic or metal components can crack, warp, or lose tension. When this happens, your dishwasher won't hold the door firmly shut, preventing proper cycles and potentially causing leaks. This replacement is straightforward for a confident DIYer, rated 2 out of 5 for installation difficulty. The main tip is to support the door panel properly with your free hand whilst removing the old lock, as the weight can strain the hinge connections if left unsupported. The part fits AEG dishwashers across multiple models and includes everything needed for a complete replacement. Before ordering, verify your appliance's E-Nr model number on the rating plate inside the door edge to ensure full compatibility with your specific machine.
Compatible with 21 models
Plinth Reinforcement,front,bottom
OEM: 140000164016
If your AEG dishwasher's front plinth has become loose, cracked, or misaligned, this replacement reinforcement is what you need to restore stability and protect the appliance's base from further damage. The plinth reinforcement supports the front bottom section of your dishwasher, and general wear over time can compromise its integrity, affecting both appearance and performance. This genuine OEM part, reference 140000164016, is designed specifically for AEG dishwashers and ensures a perfect fit and reliable durability. Installation difficulty is rated at level 2, making it manageable for most confident DIY homeowners with basic tools. When installing, ensure you fully support the dishwasher's weight before removing the old reinforcement, preventing any sudden drops that could cause injury or additional damage to surrounding components. Take photographs during removal to guide reassembly. Before ordering, please verify your dishwasher's E-Nr model number, which you'll find on the rating plate inside the door. This ensures complete compatibility and prevents any fitting issues.
Compatible with 17 models
Dishwasher Door Indicator Lamp
OEM: 1174528016
When your AEG dishwasher door light stops working, it's not just an inconvenience—it makes it harder to see inside and check on your dishes. A faulty indicator lamp can leave you guessing whether a cycle has finished or if there's an issue inside. This replacement door indicator lamp, reference 1174528016, restores clear visibility and confirms your dishwasher is operating normally. Installation is straightforward and typically takes just a few minutes. With a difficulty rating of 2 out of 10, most DIY homeowners can manage this repair without professional help. The key is ensuring you've switched off the power at the wall before starting work, and taking a photo of the existing lamp's position before removal so you can replicate the installation exactly. This genuine OEM component is designed specifically for AEG dishwashers, guaranteeing perfect compatibility and reliable performance. After years of opening and closing your door, the lamp simply wears out and needs replacing to restore full functionality. Before ordering, please verify your dishwasher's E-Nr model number to confirm this part matches your specific machine.
Compatible with 15 models
Door Outer Panel, Zinc-plated, 520x588mm,fi
OEM: 8581904032902
A worn or damaged dishwasher door can compromise both functionality and appearance. If your AEG dishwasher's outer panel is showing signs of general wear, rust, or damage, this zinc-plated replacement door outer panel is the solution you need. This genuine OEM part (reference 8581904032902) restores your appliance to like-new condition whilst protecting against further deterioration. The zinc plating provides excellent corrosion resistance, ensuring your dishwasher maintains its clean, professional look for years to come. Installation is straightforward, rated at difficulty level 2, making it a manageable DIY project for most homeowners. Our top tip: before removing the old panel, take photographs of the hinges and latch positions to make reassembly simpler and quicker. Measuring 520x588mm, this panel is designed for a precise fit on compatible AEG models. The replacement process typically takes under an hour, requiring only basic tools. Before ordering, verify your dishwasher's E-Nr model number against the compatibility information to ensure this is the correct part for your appliance. This simple check prevents unnecessary returns and delays.
Compatible with 15 models
Door Lock, Casing, with Opener, 50n
OEM: 4055977005
If your AEG dishwasher won't close properly or the door latch feels loose and unreliable, a worn door lock mechanism is likely the culprit. Over time, the lock casing can deteriorate through regular use, preventing the door from securing safely during the wash cycle. This genuine replacement part restores proper door closure and ensures your dishwasher operates normally. This OEM reference 4055977005 door lock casing includes the integrated opener mechanism rated at 50N, matching your appliance's original specifications precisely. The relatively straightforward installation means you'll need only basic tools and perhaps thirty minutes of your time. When fitting this part, ensure the door is fully open and well-supported before disconnecting the old lock assembly. This prevents accidental door closure and protects both you and the dishwasher frame from damage. Take a quick photograph before removal so you can reference the wire connections during reinstallation. Before ordering, verify your dishwasher's E-Nr model number matches the compatibility specifications. You'll find this on the rating plate inside the door edge or on the side wall of the appliance.
Compatible with 12 models
Door Hinge,kit Left and Right,
OEM: 4055474953
If your dishwasher door won't close properly or hangs unevenly, worn hinges are likely the culprit. Over time, the door hinge mechanism deteriorates through daily use, causing the door to sag, stick, or fail to latch securely. This door hinge kit addresses general wear and failure, providing both left and right hinges so you can restore your appliance to full working order. This is a genuine OEM part (reference 4055474953) designed specifically for AEG dishwashers, ensuring perfect compatibility and reliable performance. The installation difficulty rating of 2 means most confident DIY homeowners can tackle this repair without specialist knowledge or tools. When installing, remember to fully support the door with one hand whilst removing the old hinges, preventing it from dropping and causing injury or damage. Take a photograph of the original hinge position before removal to guide reassembly. Please verify your dishwasher's E-Nr model number matches before ordering, as this ensures you receive the correct part for your specific machine.
Compatible with 11 models
Dishwasher Hinge Tie
OEM: 1520419142
If your dishwasher door is sagging, creaking, or not closing properly, a worn hinge tie is often the culprit. Over time, these crucial components deteriorate from repeated opening and closing cycles, compromising the door's stability and alignment. Replacing your hinge tie can restore smooth operation and prevent further damage to your appliance. This genuine AEG hinge tie (OEM reference 1520419142) is designed specifically for AEG dishwashers and offers a straightforward repair solution. With an installation difficulty rating of just 2 out of 10, most confident DIY homeowners can complete this job in under an hour using basic tools. When fitting your new hinge tie, ensure you fully support the door with your other hand or ask someone to assist you. This prevents any risk of the door dropping unexpectedly whilst you're working on the hinges. Taking this simple precaution makes the job safer and easier. Before ordering, please verify the E-Nr model number on your dishwasher's rating plate, usually found inside the door edge or on the side panel. This ensures complete compatibility with your specific machine.
Compatible with 10 models
Door Outer Panel,zinc-plated,insulating Mat,[590mm]
OEM: 140217280019
If your AEG dishwasher door is looking worn, damaged, or no longer seals properly, a deteriorated outer panel could be the culprit. This replacement door outer panel restores both the appearance and functionality of your appliance, ensuring a proper seal that prevents water leaks and maintains washing performance. This genuine zinc-plated panel features an integrated insulating mat that helps regulate temperature and reduce noise during operation. It's a straightforward replacement job rated at difficulty level 2, making it manageable for most home DIYers with basic tools. When you're ready to install, remember to support the door fully with one hand whilst removing the old panel, as it's heavier than it appears. This prevents strain on the hinges and makes the job safer and easier. The OEM reference number 140217280019 ensures you're getting the exact part your dishwasher needs. Before placing your order, always verify your appliance's E-Nr model number matches this part's compatibility, as AEG produced several door sizes across their range. This simple check prevents ordering errors and unnecessary returns.
Compatible with 7 models
Template, Built-in
OEM: 140035669245
When your dishwasher door isn't closing properly or won't latch securely, a worn or damaged door template could be the culprit. This essential component guides and supports the door mechanism, and over time it can deteriorate from regular use, causing alignment problems and seal failures. This genuine AEG replacement template (OEM reference 140035669245) is designed specifically for built-in AEG dishwashers and restores proper door function with minimal fuss. The installation difficulty rating of 2 means most confident DIY homeowners can handle this repair in under an hour. When fitting the new template, ensure you've fully released any tension from the door hinge mechanism before removal. This simple precaution prevents accidental snapping of the component and makes reinstalling the new part considerably easier. Stock the correct replacement first time by verifying your dishwasher's E-Nr model number before ordering. You'll find this on the rating plate inside the appliance, usually on the side wall or top edge of the door opening. Matching this number guarantees compatibility and saves time on returns.
Compatible with 7 models
Door Inner Panel
OEM: 3282100712
A worn or damaged door inner panel can compromise your dishwasher's ability to seal properly, leading to water leaks and reduced wash performance. If you've noticed water pooling beneath your machine or your dishes aren't getting clean, this replacement panel could be the solution you need. This genuine OEM door inner panel (reference 3282100712) is designed specifically for AEG dishwashers and restores the integrity of your appliance's door assembly. The installation difficulty rating of 2 means this is a straightforward job for most DIY homeowners with basic tools and a little patience. When fitting the new panel, ensure you fully release all retaining clips before attempting to remove the old one, then align the replacement carefully before securing. Taking time with alignment prevents future seal problems and extends the life of your repair. This part addresses general wear and failure that naturally occurs over years of regular use. Before ordering, please verify your dishwasher's E-Nr model number matches the compatibility information for this part, ensuring you receive the correct replacement for your specific AEG model.
Compatible with 6 models
Template, Door Panel, Fully Integrated,
OEM: 140237833193
If your dishwasher door isn't closing properly or the panel looks worn and damaged, a faulty door template could be the culprit. This fully integrated door panel replacement restores your AEG dishwasher to full working order and gives it a refreshed appearance. The template houses crucial components that keep your door functioning smoothly. Over time, general wear and tear can cause it to crack, warp, or fail completely, leaving you with an appliance that won't seal properly. Replacing it is straightforward and typically takes just an hour or two. Installation difficulty is rated at level 2, meaning it's quite manageable for a confident DIY homeowner. Our top tip: before you start, take photos of how the old panel connects and remove all fasteners carefully to avoid damaging surrounding components. This helps reassembly go smoothly. The OEM reference 140237833193 ensures you're getting the exact genuine part your dishwasher needs. Always verify your appliance's E-Nr model number before ordering to guarantee compatibility with your specific AEG dishwasher model.
Compatible with 6 models
Template,door Panel,sliding Hinge
OEM: 140035669161
If your dishwasher door won't close properly or hangs at an awkward angle, a worn sliding hinge is likely the culprit. Over time, these hinges weaken through constant use, causing the door to sag or fail to seal correctly. This genuine AEG replacement hinge restores smooth operation and ensures your door closes securely every time. This is a straightforward repair suitable for most DIY homeowners, with an installation difficulty rating of 2 out of 10. The job typically takes under an hour. When you're ready to fit it, remember to support the door fully with your other hand before removing the old hinge, as it bears considerable weight. This prevents accidental dropping and potential injury. The OEM reference 140035669161 ensures you're getting the exact component designed for your machine. It's compatible with AEG dishwashers and addresses general wear and failure issues affecting door operation. Before placing your order, please verify the E-Nr model number on your dishwasher to confirm compatibility with this part.
Compatible with 6 models
Template, Built-in
OEM: 140035669427
If your AEG dishwasher door isn't closing properly or the seal has deteriorated, a worn or damaged template could be the culprit. This component helps position the door correctly and maintain a tight seal during operation. Over time, general wear and failure can compromise its effectiveness, leading to water leaks or incomplete wash cycles. This genuine OEM part (reference 140035669427) is specifically designed for AEG built-in dishwashers and restores proper door alignment. Replacing it is straightforward, rated at difficulty level 2, making it achievable for most DIY homeowners with basic tools. When installing your new template, take time to ensure the door moves smoothly through its full range before securing everything permanently. This simple check prevents misalignment issues later on. Stock this spare part with confidence knowing it's an original manufacturer component built to last. Before placing your order, verify your dishwasher's E-Nr model number matches our compatibility information. You'll find this number on the information plate inside your appliance, usually on the side wall or top edge of the door frame.
Compatible with 5 models
Template, Built-in,
OEM: 140035669583
When your dishwasher door won't close properly or the seal feels loose, a worn door template is often the culprit. This essential component keeps your door aligned and functioning correctly, preventing leaks and ensuring your dishwasher operates efficiently. This genuine OEM part (reference 140035669583) is designed specifically for AEG dishwashers and restores your appliance to its original working condition. Over time, repeated opening and closing causes normal wear, which this replacement addresses effectively. Installation is straightforward, rated at difficulty level 2, making it manageable for most DIY homeowners. When fitting the new template, take a moment to clean the surrounding area thoroughly before installation. This removes any debris or residue that could affect the seal and ensures your new part sits perfectly. The whole job typically takes under an hour, saving you considerable engineer call-out fees. You'll immediately notice improved door closure and a more secure seal. Before ordering, please verify your dishwasher's E-Nr model number matches our compatibility information. This ensures you receive the correct part for your specific appliance.
Compatible with 5 models
Door Hinge,kit Left and Right,sliding
OEM: 4055509089
Is your dishwasher door hanging unevenly or sagging to one side? Worn hinges are the culprit. Over time, the sliding hinges that support your dishwasher door deteriorate through daily use, causing alignment problems and making it difficult to close properly. This genuine AEG door hinge kit (OEM reference 4055509089) replaces both the left and right hinges, restoring smooth operation and ensuring your door closes securely. This is a straightforward repair that most confident DIY homeowners can tackle, rated difficulty level 2. The hinges simply bolt into place once you've removed the old ones. A handy tip: photograph the hinge positions before removal so you can easily reference the correct installation angles when fitting the new kit. The job typically takes under an hour and requires just basic tools. You'll immediately notice the difference as your dishwasher door glides smoothly into place rather than sticking or slamming. Before ordering, please verify the E-Nr model number on your appliance matches our compatibility information. This ensures you receive the correct replacement hinge kit for your specific AEG dishwasher model.
Compatible with 4 models
Hinge,left-right,kit,ado
OEM: 4055445847
# Zanussi Dishwasher Door Hinge Kit If your dishwasher door won't stay closed or feels loose when opening and closing, a worn hinge kit is likely the culprit. Over time, hinges wear out from repeated use, causing the door to sag or fail to latch properly. This hinge kit (OEM reference 4055445847) restores smooth operation and ensures your door closes securely again. This left-right hinge kit is specifically designed for Zanussi dishwashers and addresses general wear and failure that develops naturally throughout the appliance's life. Replacing it is straightforward, rated as a difficulty level 2, making it manageable for most DIY homeowners with basic tools. When installing, remember to support the door properly before removing the old hinges to prevent it from dropping. This simple precaution makes the job much safer and easier. This genuine part guarantees compatibility and reliable performance. Before ordering, verify your dishwasher's E-Nr model number matches the compatibility information, as this ensures you're purchasing the correct component for your specific machine.
Compatible with 4 models
Template, Built-in
OEM: 140035669492
Is your dishwasher door not closing properly or showing signs of wear around the frame? A worn or damaged door template could be causing leaks, poor sealing, or misalignment issues that prevent your appliance from working efficiently. This genuine OEM replacement template (reference 140035669492) is specifically designed for AEG built-in dishwashers and restores proper door function. Over time, these components deteriorate due to regular opening and closing, affecting the seal integrity and overall performance of your machine. Installing this part is straightforward and rated at difficulty level 2, making it manageable for most DIY homeowners. When fitting the new template, ensure you fully release the door latch mechanism first—this gives you better access and prevents accidentally damaging the new component during installation. This genuine part guarantees compatibility and longevity compared to cheaper alternatives. Before placing your order, verify your dishwasher's E-Nr model number, which you'll find on the information sticker inside the appliance. This ensures you're purchasing the correct template for your specific AEG model and avoids costly mistakes.
Compatible with 4 models
Tub Trim, Black, L=1580mm
OEM: 1526715659
When your dishwasher door doesn't seal properly or you notice water leaking during the wash cycle, a worn or damaged tub trim could be the culprit. This black trim seal runs around the inner edge of your dishwasher tub and naturally wears over time, compromising the watertight seal that keeps your kitchen dry. This replacement part (OEM reference 1526715659) is designed specifically for AEG dishwashers and measures 1580mm in length. It's an essential component that prevents water escaping during operation and helps maintain your appliance's efficiency. The good news is that replacing it yourself is straightforward. With an install difficulty rating of 2 out of 5, most DIY homeowners can complete this job in under an hour. Our practical tip: before removing the old trim, take a photo of how it sits in the groove. This reference image makes refitting the new trim far easier and ensures a properly sealed installation. Before ordering, please verify your dishwasher's E-Nr model number matches this part's compatibility list. This simple check prevents disappointment and ensures you receive exactly what you need.
Compatible with 4 models
Door Indicator Lamp, Btfd, White,
OEM: 140000781140
When your dishwasher door light stops working, you lose the convenient visibility to see inside during operation or inspect your dishes before the cycle completes. This white door indicator lamp is the genuine replacement part you need to restore that functionality to your AEG dishwasher. Over time, the lamp filament can burn out through normal use, or the component may fail due to general wear. This OEM part, reference 140000781140, is engineered to meet AEG's exacting standards and fit perfectly in your machine. Installation is straightforward, rated as difficulty level 2, making it an ideal DIY job for most homeowners. When fitting the new lamp, ensure you've disconnected the power supply first for safety. Simply remove the old unit by twisting it counterclockwise from its socket, then insert the replacement by twisting clockwise until snug. Avoid overtightening, as the fitting is delicate. This genuine component will restore your dishwasher to full working condition. Before ordering, please verify your appliance's E-Nr model number matches this part's compatibility to ensure a perfect fit for your specific AEG dishwasher model.
Compatible with 3 models
Door Lock,casing,with Opener,60n, Zm
OEM: 4055523205
If your AEG dishwasher door won't latch properly or won't open when the cycle finishes, a faulty door lock assembly is likely the culprit. Over time, the locking mechanism can wear out, preventing the door from securing during operation or releasing afterwards. This genuine replacement door lock casing with opener restores reliable operation and ensures your dishwasher functions safely. This OEM part, reference 4055523205, is specifically designed for AEG dishwashers and offers straightforward installation for most DIY homeowners. With a difficulty rating of just 2 out of 10, you'll be back up and running quickly. When fitting the new lock, take care to align the opener mechanism with the door catch before tightening everything down. This simple step prevents misalignment and ensures smooth operation every time. Before ordering, verify your dishwasher's E-Nr model number, which you'll find on the rating plate inside the appliance. This confirmation ensures complete compatibility and guarantees this part will work perfectly with your specific model.
Compatible with 3 models
Door Outer Panel, White, 564x602mm
OEM: 8581904038107
A worn, cracked, or discoloured dishwasher door can let down the whole kitchen. If your AEG dishwasher's outer panel has suffered general wear or damage, this replacement part will restore both its appearance and functionality. This genuine OEM door outer panel (reference 8581904038107) is designed specifically for AEG dishwashers and measures 564x602mm. Installation is straightforward, rated at difficulty level 2, making it an achievable DIY project for most homeowners. Before you start, take a clear photograph of your dishwasher's current door assembly from different angles. This helps when removing the old panel and ensures you're reassembling everything correctly. You'll need basic tools like a screwdriver and possibly a plastic trim removal tool to access the fixing points. The job typically takes 30 to 45 minutes once you've gathered your tools. Always switch off the appliance at the mains before beginning any work. Please verify your dishwasher's E-Nr model number matches our compatibility information before ordering. You'll find this on the product data sheet inside your appliance.
Compatible with 3 models
Latch, Door
OEM: 140035300122
Your dishwasher door won't close properly or keeps popping open during the cycle? A worn or broken door latch is usually the culprit. Over time, the latch mechanism can deteriorate through regular use, preventing your door from securing correctly and causing your appliance to malfunction or refuse to run. This genuine OEM door latch (reference 140035300122) is designed specifically for AEG dishwashers and will restore proper door closure and operation. It's a straightforward replacement that most confident DIY homeowners can tackle in under an hour, rated at difficulty level 2. When installing, we recommend taking a photo of the existing latch before removal so you can easily identify the correct orientation when fitting the new one. This simple step prevents frustration during reassembly. The latch is a common wear item that doesn't require any special tools or plumbing knowledge to replace. Before ordering, please verify your dishwasher's E-Nr model number matches our compatibility list to ensure you're purchasing the correct part for your specific AEG model.
Compatible with 3 models
Dishwasher Hinge Tie
OEM: 1520419209
If your dishwasher door won't stay properly aligned or hangs at an awkward angle, a worn hinge tie could be the culprit. Over time, this small but essential component deteriorates through regular use, causing the door to sag or fail to close smoothly. Replacing it restores proper door function and prevents further damage to your appliance. This genuine AEG hinge tie, reference 1520419209, is a straightforward repair that most confident DIY homeowners can tackle. The installation difficulty is rated at just 2 out of 10, meaning you won't need extensive experience or specialist tools. The job typically takes less than an hour. When installing, make sure to support the door properly before removing the old hinge tie so it doesn't drop unexpectedly. This prevents injury and protects your kitchen floor from damage. We stock this part to the highest standards, ensuring reliable performance and longevity. Before ordering, please verify your dishwasher's E-Nr model number against our compatibility list to guarantee this is the correct component for your appliance.
Compatible with 2 models
Door Outer Panel, Inox, 589x602mm
OEM: 8581904038008
If your AEG dishwasher's door looks worn, discoloured or damaged, a worn outer panel could be letting the side down. This stainless steel replacement restores your appliance's appearance and functionality, whether you're dealing with general wear from years of use or visible failure affecting the door's integrity. This genuine OEM part (reference 8581904038008) is designed to fit perfectly on compatible AEG models, ensuring a professional finish that matches your original specifications. Installation sits at difficulty level 2, making it manageable for most confident DIY homeowners with basic tools. When fitting the new panel, start by carefully removing the old one—it's typically secured with clips or screws around the perimeter. Take a moment to inspect and clean the underlying door frame before installing the replacement, ensuring a smooth, properly aligned fit. Before ordering, verify your dishwasher's E-Nr model number matches our compatibility information. You'll find this on the appliance's rating plate, usually inside the door edge. This simple check guarantees you're purchasing the correct part for your specific model, saving time and frustration.
Compatible with 2 models
Fitting Instruction
OEM: 140035669138
# Fitting Instruction When your dishwasher door isn't closing properly or latching correctly, a worn fitting instruction component could be the culprit. Over time, door parts experience general wear and failure from repeated opening and closing, compromising the seal and performance of your appliance. This genuine OEM spare part (reference 140035669138) is designed for Electrolux and Zanussi dishwashers, restoring reliable door operation and ensuring your machine functions as intended. The installation difficulty is rated at level 2, making it manageable for most DIY homeowners with basic tools and mechanical confidence. When fitting this part, take time to carefully align all components before fully tightening them down. This prevents misalignment issues that could cause the door to sit unevenly or fail to close smoothly. Working slowly at this stage saves frustration and ensures a proper, long-lasting repair. This straightforward fix can save you significant expense compared to calling out an engineer. Before placing your order, verify your dishwasher's E-Nr model number against the compatibility information to ensure you're purchasing the correct part for your specific machine.
Compatible with 2 models
Door Hinge,kit Left and Right
OEM: 4055474946
If your AEG dishwasher door has become loose, won't close properly, or appears to be sagging, worn hinges are likely the culprit. Over time, the hinges that support your door can deteriorate through regular use, causing alignment issues and potential damage to the seal. This genuine door hinge kit (OEM reference 4055474946) replaces both left and right hinges, restoring your dishwasher to full working order. Replacing door hinges is a straightforward task rated at difficulty level 2, making it perfectly manageable for most DIY homeowners. You'll typically only need basic tools and around 30 minutes of your time. A helpful tip: before you begin, take a photo of the original hinge positions so you can easily match the alignment when installing the new kit. This replacement part is specifically designed for AEG dishwashers and comes as a complete left and right hinge set, saving you the hassle of ordering components separately. Before ordering, please verify your dishwasher's E-Nr model number matches our compatibility information to ensure you receive the correct part.
Compatible with 1 model
Door Outer Panel, Inox, 437x614mm
OEM: 8581904033009
If your AEG dishwasher door is looking worn, dented, or discoloured, a replacement outer panel can restore its appearance and protect the inner mechanisms. Over time, these stainless steel panels accumulate scratches, handle marks, and general wear that affect both functionality and aesthetics. This genuine OEM part (reference 8581904033009) is designed specifically for AEG dishwashers and measures 437x614mm. Installation is straightforward, rated at difficulty level 2, making it manageable for most DIY homeowners with basic tools and patience. Before you begin, ensure you've isolated the power supply completely for safety. The panel typically attaches with a few screws and clips around the door frame. Take your time aligning it properly before tightening everything down, as this prevents gaps that could affect door closure. This is a popular solution for addressing general wear and failure of the external door surface. Whether you're dealing with cosmetic damage or functional issues, replacing the outer panel breathes new life into your appliance without the expense of a complete unit replacement. Always verify your dishwasher's E-Nr model number matches this part before ordering to guarantee compatibility.
Compatible with 1 model
Door Outer Panel, White, 437x614
OEM: 140001351042
If your AEG dishwasher's door has become scratched, cracked, or simply worn after years of use, replacing the outer panel is a straightforward way to restore its appearance and functionality. This genuine replacement panel (OEM reference 140001351042) is designed to fit perfectly on compatible AEG models, giving your appliance a fresh look. The installation difficulty is rated at level 2, making it manageable for most confident DIY homeowners. The job typically involves removing the old panel and securing the new one in place. One useful tip: before you begin, take photographs of how the existing panel is attached, as this will guide you when fitting the replacement and ensure everything lines up properly. This white panel measures 437x614mm and will address general wear and failure issues affecting your dishwasher's exterior. It's a cost-effective solution compared to replacing the entire door assembly. Before ordering, please verify your dishwasher's E-Nr model number matches the compatibility requirements. You'll find this number on the appliance's rating plate, usually inside the door frame. This ensures you receive the correct part first time.
Compatible with 1 model
Door Outer Panel, White
OEM: 8581904033504
A cracked, dented, or discoloured dishwasher door can make your kitchen look tired and may indicate deeper wear affecting the seal's integrity. This genuine AEG replacement door outer panel restores your appliance's appearance whilst ensuring proper operation. Over time, the outer panel bears the brunt of daily use, from accidental knocks to general weathering. When yours shows signs of damage or cosmetic failure, this OEM part (reference 8581904033504) offers a straightforward solution that maintains your dishwasher's performance and aesthetic appeal. Installation is straightforward for most DIY homeowners, rated at difficulty level 2. The panel simply clips and screws into place, typically requiring just a Phillips head screwdriver and roughly 20 minutes of your time. One helpful tip: carefully support the panel during installation to avoid straining the hinge mechanisms whilst you're securing it. This genuine AEG component ensures perfect compatibility with your machine, delivering the quality fit you'd expect from a factory-original part. Before ordering, please verify your dishwasher's E-Nr model number matches our compatibility information to guarantee this is the correct part for your appliance.
Compatible with 1 model
Door Outer Panel, Zinc-plated, Fi 60, 520x588mm
OEM: 8581904033306
A damaged or worn dishwasher door panel can let your kitchen down, creating an unsightly appearance and potentially affecting the appliance's performance. This genuine zinc-plated outer door panel is designed to restore your AEG dishwasher to like-new condition, whether you're dealing with dents, rust, or general wear and tear from years of use. This replacement panel, measuring 520x588mm and referenced as 8581904033306, is a straightforward repair that most confident DIY homeowners can tackle in under an hour. The installation difficulty rating of 2 means it's one of the more accessible dishwasher repairs available. When fitting your new panel, remember to carefully disconnect the door catch mechanisms before removal, as this will save you considerable frustration during reinstallation. Take a photograph before you start so you can reference the assembly when putting everything back together. Before placing your order, please verify your dishwasher's E-Nr model number against the product specification. This ensures you're ordering the correct compatible part for your specific AEG model, avoiding any unnecessary delays or returns.
Compatible with 1 model